Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi,
1.I want to develop the my product using nrf51822 with PCB antenna(as shape given in sdk hardware) with following board stackup-
2. i am going to use cap-0603 in...
Hi,
I am using nrf52840 S140 PCA10056 SDK 15.2.0 version with example ble_app_multirole_lesc_S140_PCA10056 . i am using Segger Embedded studio IDE. So now problemis i am...
Hi,
I am trying to get my systemOFF current below 1uA, but Im struggeling.
normally I use MBED, but to eliminate that variable, I just did a test without MBED, I took...
Hello together, I am experiencing problems with the nrf52840. I got the BLE_APP_Blinky example to run. Now I am trying to get the BLE_THROUGHPUT example experiment to run...
Dear nordic,
I want to know something regarding your SDK. I have nrf52832 development board and i use sdk 15.2 .
1. if i want to use BLE 4.2 version what changes i want...
Hi,
I am working on a project where my mobile phone will be acting as a central device and nRF52840 DK will be acting as a peripheral device. I added the UART example to...
Hi,
I am working on a project where my mobile phone will be acting as a central device and nRF52840 DK will be acting as a peripheral device. I used the nRF UART and nRF...
Dear nordic,
I need more information regarding this?
1. I heard the BLE one packet has possible 20 bytes. but i tested this example and connect using nRF connect app...
Hello everyone,
I am experiencing a weird problem; I am working on an NRF52840 DK board and writing my code in Segger Embedded Studio.
I do not have any problem when...
Hi,
I am looking for the nRF52 / nRF52 Mesh online courses.
I am going to developing a new project based on MESH network. where i required lot of sources to clarify my...
Hi, I'm using the nRF52 SDK 15.3.0's BLE_APP_UART central/peripheral examples with my PCA10040 boards.
Can I ask about the central example, please?
0. Currently, I think...
hi guys, I'm looking for understand how to send a simple signal using the 802-15-04 between two nrf52840 boards.
The only available example use the uart in order to have...
I have modified the Blinky example in the SDK to support CODED_PHY as per the examples I have seen but am unable to get it to run. The modified main.c is attached
It seems...
Is there an example layout using the nRF52840 that does not use microvias and via-in-pad technology? My application is high volume, and I am trying to keep PCB costs low.
Hello,
I am using nrf52832 and nrf5 SDK12.3 to develop my project.
When I debug it in SES and it works well,but when I stop debug or close SES or power off and power on...
