Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Updates are moved to the end of the question
I created a modified version of pca10028.h and boards.h and have preprocessors changed so that the following new config is...
I example test ble_central and ble_peripheral of ble_app_uart.
Radio TX and RX test is OK.
It confirmed the data communications relating to uart_event_handler function....
I'm trying to get a time stamp using app_timer_cnt_get(&ticks), but the ticks always equals 0. And I have called APP_TIMER_INIT() to init the app timer. I have no idea why...
Hi everyone, I have been given a nRF51-DK board and I should use it to send data retreived from a sensor to it through Arduino, to finally receive it in my cell phone. I am...
Hello everyone,
I'm brand-new here. I have developed quite a bit of software on desktop PC's, but this is my first experience with embedded programming. A few weeks ago...
Hi Team,
So I downloaded the new nRF Connect for OSX. I inserted my PCA10031 nRF51 dongle into my USB port and the relevant lights lit up. However nRF Connect does not...
I am quite new to embedded firmware development and definitely just two days old into Nordic nRF52 development.
I want to just setup a 25% duty cycle clock output on GPIO...
Hi,
I have a very sophisticated program on nRF51822 with SD120 which uses SPIS (as an RX for another board) and UART. I used "spi_slave_example" as a base program.
I am...
Hi, in the (not great) mBed PWM driver, when setting up GPIOTE to toggle the output pin they do this:
/** @brief Function for initializing the GPIO Tasks/Events peripheral...
Hi,
I have a application that needs to advertise only for 120 seconds and on change in values of accelerometer , it needs to start advertise again.
presently i have a...
Hi,
I've been using these parts for a few years (the 51) and recently did some work getting the boot loader to be joined together with the application into a single burnable...
Hi,
I wish to exchange the sensor form mma7660 to hmc5883l, so I simply replace it with my own function just like mma7660 did.
Those function are
define HMC5883L_ADDR...
Dear All.
As I know, nRF52 support PDM mic. So, I'll make recording sound with nRF52.
But, I do not find PDM example on SDK 11.
Please notice me, where is the PDM mic...
We are using the NRF51822qfaag0 ic and softdevice 7.3 with sdk 6 . We are able to do dfu using the android device with nrftool box apk. But we have to do dfu from windows...
Hi There
I am working on NRF9E5-EVKIT-868/915, suddenly I faced a problem where it stop running any burned program. It is successfully programmed and verified but nothing...
