Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
Hello,
I'm currently porting all my C++ code from SD130 SDK10 to SD132 SDK12 and I also upgrading from device_manger to peer_manager.
I've noticed that in peer_manager_types...
Hello,
It seems that NRF_LOG_BACKEND_SERIAL_UART_BAUDRATE has wrong documentation. In sdk_config.h it says:
// <o> NRF_LOG_BACKEND_SERIAL_UART_BAUDRATE - Default Baudrate...
Dear Nordic Team,
Thanks for support.
I want to know the possible for nrf52832 act as a sniffer. If it is possible means i want to latest sniffer hex code.
Dear Nordic Team,
Thanks for support.
I have tested Current Time Profile sample application whenever connect with nRF connect APP the debug widows shows always "Current...
Good morning all,
We have a circuit based on 51822 chip.
We are currently trying to monitor some value from 0v to 24v from the analog inputs.
It's working, however...
I recently saw that SDK12.0 provides a Bootloader Cryptography module. I'm not certain after reading the documentation that this module can support my use case:
infocenter...
Hi,all. i want to use nrf51822 to generate a 3.3M hz wave,but i don't know how to do this.Can this chip reach so high frequency？Can someone help me? Thanks ！
I'm trying to implement context switching from handler mode to thread mode using PendSV. I set the PendSV pending bit inside an ISR with SCB->ICSR = SCB->ICSR | SCB_ICSR_PENDSVSET_Msk...
Compiling nordic project I get errors:
compiling main.c...
..\..\..\main.c(37): error: #5: cannot open source input file "softdevice_handler.h": No such file or directory...
I am not sure if this is a limitation with Keil or Nordic SDK. I made another copy of ble_app_uart inside SDK_11 s130 and renamed it with a much longer name. I tested that...
I'm using the nRF SDK5 v11.0.0.
I'm trying to test out UART Logging in the simple blinky example bundled in the SDK.
I added NRF_LOG_INIT() and then a NRF_LOG("Testing\n...
Hello everyone,
I am trying to implement a bootloader to my application to be able to enter in DFU mode.
I am using nrf51822 (32KB ram 256 flash) and s130.
I have taken...
My understanding is that the nRF51 is known to need a fairly stiff external pull-down resistor on SWCLK to avoid noise putting the chip into debug mode. I note that the nRF52...
I'd like to know how to implement a bootloader for the Nordic SoC nRF51822-QFAA-R in order to boot the softdevice and some firwmare. If will be great getting an application...
Does nRF52832 have battery monitor?
I can't find in the datasheet if there is an externarl circuit to monitor the battery. I'm using a CR2032 coin cell battery.
Tha...
