Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Hi,
I noticed that I can't bond successfully with my device using iOs 9.1 with Nrf Master control panel iOs app. When I insert the PINCODE, the device immediatly disconnects...
So I just received my nRF51 dk. When I plug it into the USB port, the device starts to blink but is not showing up as standard USB drive? Any suggestions?
Gabriel
Hello,
what general setup can you recommend to realize a Final Product Test only with BLE for mass production! (Without any additional copper contacts or NFC)
Some facts...
Hi I was reading up on all your chips.. NRF24, BLE and also on IPV6 capable..
Below are my requirements. Can you make a recommendation on what setup to use?
I have 4...
Hi
Im developing a filter - repeater signal on S130, and I want to advertise with a peridod of 20 ms for 10 seconds timeout.
I'm confused with FAST ADVERTISING AND SLOW...
HI ,ALL
i need to take use of the pstorage module.
i can read the data after reset,but i do not know the reason.
the write function is added in the on_write...
Hi there,
I have a nrf51422CEAA chip with 16k variant with single bank bootloader code. I compile it using (03) optimazation and the final result is :
"Program Size...
Hello,
I just produced my custom board with nRF52 but i have a problem.
I can program it (SWD over nRF52 DK), debug it (segger debudder software) but in bootloader it...
hi there,
I am using this tutorial to add dfu to nrf51422_xxac_s130 beacon application. however Im getting these linking errors:
._build\nrf51422_xxac_s130.axf: Error...
I was wondering what the procedure it for questions asked over the weekend. Obviously you guys are only available at office hours (Norway time I'm guessing?), so how do you...
I was kindly surprised with new S130 functionality - ECDH key exchange. Do you have plans in the near future to implement it in S110 softdevice? Thanks
Hi
I have nrf51822 CEAA which is powered with 1.9 volt on vdd (low power chip). I'm using ADC to measure battery level but the conversion gave me 5.4 volt wich is wrong for...
Hi,
we have developed some software that is running fine on the nRF52-DK (PCA10040 v0.9.0) which uses nRF52832 IC revision "Engineering B".
We are using SoftDevice s132_nrf52_2...
Hey everyone,
I am using nrf51 dongle pca 10031. Nordic promised to have 1Mbps data rate. when i was trying to transfer data through UART. data is validated until 401600...
hi
im working with nrf51422 and keil and s130
my external crystal is a 32768 and 16 mega
for my soft-device witch one should i use
// Initialize SoftDevice.
SOFTDEVICE_HANDLER_INIT...
