Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Dear Nordic,
I have a Thingy91x. I tried flashing the nRF9151 SoC on the device but ran into error messages. I realized that the nRF53/nRF91 switch was in the nRF53 position...
Hi,
I'm trying to implement a Firmware Erase and Update procedure using the nRF52832 module on a custom board. In the Nordic Devzone I've been following the steps to do...
Hello!
I have designed a custom board with the nRF5340 , powered at 1.8V. I am able to program the chip successfully, but after the firmware is downloaded (Zephyr RTOS,...
We are currently implementing the 9151 SIP into our design, and we am noticing some discrepancies between the datasheet and the evkit schematic. I am hoping you can help us...
Hi Nordic team!
Is there any way to dynamically change the charging current while the charging is ongoing? BCHGISETMSB and BCHGISETLSB can be changed only if charging is...
Hello,
We have an nrf522840 board using retained memory feature following this sample and using the NRF_RETENTION setting:
https://github.com/zephyrproject-rtos/zephyr...
Hi,
My project is based on NRF52832 with SDK11.
I got 2 working units, 1 is advertiser and 1 central.
The advertiser is advertising every 2 second.
The central unit...
Hi all,
We've followed the reference EVK designs closely and are now in the Pre-Production phase.
The initial development board was intentionally large to accommodate...
Hi Nordic Team,
I am using NCS v3.0.0 and working on a Matter-based application.
I have enabled the ActiveHardwareFaults attribute (0x0005) in the General Diagnostics...
Hi, Goal: Send a firmware update from nrf5340 to another nrf5340 over BLE I found the following sample and a lot of support tickets talking about this sample but I am unable...
hi support team,
i have customer is developping mesh.
customer is trying to sniffer the message when i pressed the buttoon on demo mesh_light.
i have two questions on...
Hello,
I recently tried some examples with nRF53 + nRF7002 (e.g. ble_coex example).
However, I am developing with nRF54 and I would like to understand if the combo nRF54...
Hello,
Recently, my team has been struggling with an issue regarding a nRF5340 device that's encapsulated and inaccessible to be flashed with a JTAG connection. Our normal...
I am working with the DWM3001CDK board for Ultrawide band, but would like to use one of the free LEDs on (P0.14, P0.22, P0.05, or P0.04) as a way to show that the 3 AAs powering...
Hi,
We’ve designed a project using the nRF5340 + nRF7002 combination, with Wi-Fi connectivity enabled.
As part of our preparations for FCC certification, we’re currently...
