Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hi,
I am currently developing a custom Zigbee end device with support for FOTA updates. My FOTA seems to work (all data gets transferred correctly) but the update won't...
Hi guys , another question here regarding Cmock and opaque types . I am currently trying to mock a function with an argument that contains the type "struct bt _conn " . However...
The hardware I use is nrf52840Dongle, using nrf_dm sample for development. There are a few problems:
1. I have 8 devices, all within communication range, 4 as base stations...
Hi,
I am running the stock UDP example on a nRF9160-DK (PCA10090, 0.8.5, 2019.7, Modem FW 1.3.6) and the modem crashes immediately.
I have also tried the CoAP example...
I have bought an nrf9161-dk and following the documentation, I was installing the asset tracker using nrf-desktop v.4.4.1 (because v.5.0 crashes everytime I open it in full...
Hi,
We have an nRF9161DK and received our own custom boards this week. When we tried to program our custom board, the development kit disconnected from the computer and...
Hi,
im use nrf52840 develop my product,and now my pcb is ready,but after some times program, it cant be programmed,also nrf connect and vs code .im try ti recover it by...
Hi
im develop my product base nrfdesktop of ncs,i build the project and program to the nrf52840DK,it can run and perform funcation.but when i program it to my board,it cant...
Hi,
I am trying to connect and acquire the signal from the Adafruit I2S MEMS Microphone using I2s communication with my board (nRF5340 DK). Because I am new in this controller...
This is a continuation of the following ticket: The resolution was logged as DRGN-19197, which was part of v2.4.0 , but did not resolved the issue.
I have created a minimal...
Hello,
Using the sample PSA Protected Storage on the nrf5340 DK with NCS v2.6.1 (and v2.5.2). My prj.conf contains these settings:
I flash the sample provisioning_image...
Hi,
I am using Nordic nRF52833 as a peripheral which uses mcuboot and DFU over BLE. I can easily upgrade firmware on that device by connecting to it with nRF Connect mobile...
Hi,
I use nrf52833 Development board PCA10100 to do loss test as peripheral and speed is 1Mbps, tx power is MAX. It's loss rate is very high, when nrf52833 sends a packet...
Hi, I am trying to use the periodic advertising connection examples and get Hci errors: opcode 0x2036 status 0x01 Failed to create advertising set (err -5)
I am on NCS 2...
Hi:
I checked the zephyr.dts file, but I couldn't find the addresses for interrupt-controller(0x e000e100 ) , timer(0x e000e010) , and memory(0x20000000) in the nRF9160...