If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hello!
Does anyone know of a library for the I2C LCD 16x2 display? I found the library by lovee, https://devzone.nordicsemi.com/f/nordic-q-a/23401/nrf52832-connect-with...
Not really sure where the problem is here, my guess is in the code... I just recently saw this: https://www.avrfreaks.net/comment/1342846#comment-1342846
Although my issue...
Hi there,
I'm in the midst of migrating between SDK14.2->15.2, and SD 5.1->6.1
I'm calling sd_flash_write() and sd_flash_page_erase() before enabling the SoftDevice with...
Hi,
I start a new design using the nRF Connect Sdk instead of the nRF5 Mesh Sdk.
Is it possible to provision a device over the mesh network using the NCS (like the PB...
After LPN publishes message, NRF_MESH_EVT_LPN_FRIEND_POLL_COMPLETE event is generated five times. Also I noticed that instead of transmitting single publication message LPN...
Hi,
We have a problem with a nrf9160 connected in NB-IOT with a bad signal.
During the debugging session to try to figure out what happen, we saw that the mqtt_evt_handler...
Hi everyone,
I have a problem since a couple of day with an interrupt of app_timer not triggering when adding a BLE central to my project. The device is working well as...
If I can get time through WiFi then send it to the nRF5340 and place it in a Struct TM. is there any method to have the nRF5340 maintain the time/calendar from that initial...
I'm sorry. This must be trivial to all of you. I'm a beginner with nrf52 programming, and I saw several examples that refer to timers TASK_START, TASK_CLEAR, TASK_STOP. Everywhere...
Our device has both a 9160 and a 52840 on it.
The 9160 is running the stock serial modem firmware on it.
The 52840 is running a custom handler for AT connection targeted...
Hello,
We are doing some network quality tests on LTE-M with PSM off and notice loss on UDP between 0% to sometimes 15% on simple udp messages sent every 10 seconds from...
It is not very clean to start a work_q with no name when all others name them properly, or at least put in the name of their k_work_q struct. Working with system threads it...
Hi,
I'm upgrading my firmware from sdk1.7.0 and there is one error that i can't solve and need your help.
The code is working on SDK1.7.0, solved all the errors that appeared...
Hi,
I have a nrf5340 device which is built with nrf Connect SDK 1.6. I can successfully DFU over ble by nRF Connect mobile app. Right now, I am trying to do DFU from my...
Hello,
I am attempting to configure a project with full zephyr logs (using RTT backend). I am, however, unable to get the full logs (see example below):
[00013022] <dbg...
Hi,
I have enabled SPIM on nRF52810 and worked normally.But when I enabled on nRF52832, it worked unusual.
I had defined CONFIG_NFCT_PINS_AS_GPIOS because used P0.9 and...
Hello,
We are using lwm2m client project SDK version v1.9.0. We need to enable #define CONNMON_LAC 12 to get LAC value but i am facing problem to enable #if defined(CONFIG_LWM2M_CONNMON_OBJECT_VERSION_1_2...
