Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi
Im developing a filter - repeater signal on S130, and I want to advertise with a peridod of 20 ms for 10 seconds timeout.
I'm confused with FAST ADVERTISING AND SLOW...
HI ,ALL
i need to take use of the pstorage module.
i can read the data after reset,but i do not know the reason.
the write function is added in the on_write...
Hi there,
I have a nrf51422CEAA chip with 16k variant with single bank bootloader code. I compile it using (03) optimazation and the final result is :
"Program Size...
Hello,
I just produced my custom board with nRF52 but i have a problem.
I can program it (SWD over nRF52 DK), debug it (segger debudder software) but in bootloader it...
hi there,
I am using this tutorial to add dfu to nrf51422_xxac_s130 beacon application. however Im getting these linking errors:
._build\nrf51422_xxac_s130.axf: Error...
I was wondering what the procedure it for questions asked over the weekend. Obviously you guys are only available at office hours (Norway time I'm guessing?), so how do you...
I was kindly surprised with new S130 functionality - ECDH key exchange. Do you have plans in the near future to implement it in S110 softdevice? Thanks
Hi
I have nrf51822 CEAA which is powered with 1.9 volt on vdd (low power chip). I'm using ADC to measure battery level but the conversion gave me 5.4 volt wich is wrong for...
Hi,
we have developed some software that is running fine on the nRF52-DK (PCA10040 v0.9.0) which uses nRF52832 IC revision "Engineering B".
We are using SoftDevice s132_nrf52_2...
Hey everyone,
I am using nrf51 dongle pca 10031. Nordic promised to have 1Mbps data rate. when i was trying to transfer data through UART. data is validated until 401600...
hi
im working with nrf51422 and keil and s130
my external crystal is a 32768 and 16 mega
for my soft-device witch one should i use
// Initialize SoftDevice.
SOFTDEVICE_HANDLER_INIT...
I'm trying to add a characteristic to a service in nRFGo Studio with the Write propery enabled.
However, the software doesn't allow me to enable Write and greys the checkbox...
Hi,
i am using nrf51822 for my application.
i am using connectable undirected mode with 40 ms advertising interval but when i am seeing the device data in the nrf master...
hi,
i am using sdk 10, with s120.
i want to advertise data on a single channel with frequency say (2426).
is there any sample code or something, with which i can play...
Is there a hook anywhere in the SD (130/132) to let me generate my own LTKs, EDIV and RAND during the bonding process? I don't think so, I've not found one, but perhaps I...
