Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
I am attempting to advertise two sets, one using coded PHY and one using 1M, currently using the master NCS branch (post v1.7.0-rc2 tag). This is on a custom board with an...
Hello,
I have got the exact same issue as described here: https://devzone.nordicsemi.com/f/nordic-q-a/58275/zigbee-reporting-not-work-while-using-multiple-endpoints/236706#236706...
I'm running FreeRTOS with default tickless idle mode (CPU is woken up by SysTick interrupt) on NET_CPU core.
If the TAD_S module (Trace and debug control) is not enabled...
Hi Nordic team
Last week and before, I tried sdk connect v3.0.0 http_application_update example.
Everything was fine. Pressed button1 to download new bin file and then...
HI DEV
Currently we found a UART Frame error on customer product:
Application scenario diagram
Figure1
nrf52820 ,SDK17.02, softdevice:S132 , gap event length=6*1...
Hi! I'm new to zephyr and nRF boards.
I am trying to write a custom board using the nRF52811. When I try to build examples using the custom board using the command (syntax...
When I asked earlier, it was not possible to send HTTPS payloads greater than 2K due to the TLS secure socket buffer size limit. I see in the most recent modem firmware release...
I'm using nrfjprog version: 10.13.0 / JLinkARM.dll version: 7.50a to flash a firmware onto a custom PCB with nRF52840. Programming hardware is a nRF52840 DK. Our firmware...
Hi,
I am sensing interrupts on a pin using GPIOTE. I can see the interrupts coming on the oscilloscope. The firmware also detects the interrupts. However once I am inside...
Is the IXIT for RF of nrf52832 correct bellow? The test house said the value of inband image frequency should 4Mhz.
IXIT for RF
IXIT Reference
Identifier ...
in \nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8\examples\zigbee\experimental\cli\cli_agent_router example , we use the nrf52840 dongle as the Coordinator, for joining the...
what happened when I create a kernel timer (based on the 32k RTC) by nrf connect sdk on nrf 52840 dk?
static const struct k_timer my_timer; static const struct k_work my_work;...
Hi All,
Im pretty new to embedded systems and currently trying to connect a TE MS5837 30B pressure sensor to a nRF52840DK (pca10056) which is all being done via Segger ...
Hello,
I am using openocd to flash nRF52 DK, however, I have several devices connected to my pc at once and I can't figure out how to flash just one of them, When a single...
