Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
I have a photodiode, and under indoor lighting conditions, the reading on the oscilloscope is about 150mV. When I connect it to an Arduino Uno or Adafruit nRF52840 Sense,...
I built an application on the NRF52 Development Kit.
I was using the old NRF serial application with the retargetio.c file to push data out through the serial port.
I...
I have been looking at BLE with the Nordic products from the perspective of someone who gets a hand wave of an idea and moves forward. I have developed Nordic firmware but...
We have been able to enable coded phy with PAWR using
```
struct bt_le_adv_param *params = BT_LE_EXT_ADV_NCONN; params->options |= BT_LE_ADV_OPT_USE_IDENTITY | BT_LE_ADV_OPT_USE_NAME...
Hello,
I'm using nrf52840 DK to test 1khz tone. The nRF Connect SDK version is v2.6.0.
I put a pcm raw data array of 1khz tone in the code and used i2s write to send the...
Hi everybody. Recently, I've spent nRF Connect SDK Intermediate online course. I could add firmware upgrade ability using FOTA and now, I can update the firmware using nRF...
Hello,
I am using nrf5340 audio sample with the custom board. The nRF Connect SDK version I used is v2.7.0.
I referred to this post and tried to add skyworks fem to my...
Hi Nordic Semiconductor Expert,
I would like to measure the BLE throughput over nRF52805.
Seeing BLE Throughput sample in nRF Connect SDK below, this SoC platform is...
I am developing with the nRF5340, but I am encountering an issue where CONFIG_BOOTLOADER_MCUBOOT is not being enabled. Although I have enabled it in the prj.config file as...
Hey, I am trying to run F8100 development board with nrf52840 development board, while I make the connection simply like CS-D10(Arduino pin layout presenting), MISO- D11,...
Hello. I would like to receive the passkey value that the user entered when pairing Bluetooth and modify it. Originally, it was said that if you enter "0000", you have to...
Dear support team,
I'm using nrf9160 and SLM to create a UDP server and client, and communicating between them. When communicating every 300 ms, there are times when there...
Hi, I got a problem with the NRF Connect plugin for VSC.
I have a project which has that structure:
workspace ├── app │ ├── src │ │ └── main.c │ ├── CMakeList.txt │ └...
Hello everyone,
I am working with nrf connect sdk toolchain v2.6.1.
My project requirements are as follows:
1 MBaud UART Async API
Two Modes for UART RX
fill...
Hello, I installed the the toolchains 1.9.0(working on existing project) successfully. However, i am not able to install manage SDKs.
This is my output:
