I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi,
i'm using SDK11 with NRF52832
After a pin falls from HIGH to LOW The GPIOTE_IRQHandler calls a function in my program to read 8 bits from the bus (Inside the interrupt...
Following the seminar today I tried to build and run this example.
built on command line using west (non-secure nrf9160-DK target)
in a continuous loop I get
```
SPM...
I want to dump lengthy log data out through an RTT connection if the JLink is connected but NOT spend that time if there's no physical RTT channel present. The idea is that...
1.Customers need to use nrf52833 for design and production in this package: WLCSP package, 3.175 x 3.175 mm
2.I noticed the description in this manual:nAN-38 WLCSP Handling...
At present, the SMS is sent normally. The format of nrf9160 is 7bit, and can send a maximum of 160 characters. However, how to send it in packages if the content exceeds 160...
We are looking for a Bluetooth 5.1 indoor positioning solution at precision around 1m.
Could you help figure out which platform/reference design is capable of implementing...
Hi,
I have configured the MQTT simple sample from nordic to send data to our broker, this works just fine at the moment.
I would like to send Json formated data to the...
Hi all,
I was playing around with radio and trying to create interupts for the event_end flag and i've now messed up completely and even without the code i added the chip...
I am working with the PWM driver to drive a stepper motor and I have a couple of doubts about when all the events are generated. My doubts are related to events:
NRF_PWM_EVENT_SEQEND0...
Hi,
I try to implement a disconnection after wrote a characteristic parameter. This byte change the working mode of my systeme.
So user connect, write the field to change...
Hi everyone,
I'm working on a BLE application using nRF52840. This application actually run with nRF SDK15 and we need to upgrade it to SDK16.
I followed Migration guide...
Hi,
We currently have a project that uses nRF52832 in audio. There are currently two questions that need to be confirmed.
first question:
Because other chips on the...
Hi,
The Ai0, and Ai1 inputs can be used as voltage references for COMP feature. Is there a way to use input Ai0/Ai1 as reference voltage for SAADC?
Thanks in advance...
Hello! I need to migrate the loader project from SDK15.3 to 16.0. The SES project parameters are as follows: FLASH_PH_START = 0x0 FLASH_PH_SIZE = 0x80000 RAM_PH_START = 0x20000000...
On a custom board based on nrf52840.
We want to write data on a SD CARD every XX seconds.
We implement this by changig the state of a state_machine at every wakeup from...
