Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
Hi,
I am working on internal flash nRF52832 merged with twi sensor, my sensor function will return a string . How to assign the string to the my_data.p_data . i am getting...
Developing on the nrf51822
Have working code for the nRF52840 Dongle using the pc-ble-driver therefore all Bluetooth work is done using sd_* calls. The PC provides easy...
Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
While debugging the code with Nrf connect extension in VS code , code get stuck at the start only does not go any where getting the SIGNTRAP error continuous
HI,
I am building "esb_ptx" sample in NRF54L15-PDK, by using CONFIG_DYNAMIC_INTERRUPTS, but it;s always reset like below;How to config the prj.conf to enable CONFIG_DYNAMIC_INTERRUPTS...
Dear all:
I found that the nrf52840 flash size is only 1MB, but the size of light bulb load is about 850KB, I have some questions:
1. Does it contains the FOTA region...
Hi
I am trying to use nrf52811 using nrf52840 DK board.
First, I check simple GPIO example working on my nrf52811 based custom boards
Second, I checked the Bluetooth...
How can I execute a command to commission a device for Thread by using the QR code or pairing code? (without using the pin_code or discriminator) Thanks.
Hi I want to run an epaper with the nRF52832 therefore is SPI needed. Board file was generated from scratch. In the devicetree I added the SPI modul and a epaper modul, which...
Hi,
I am seeing a strange issue with nRF52840 Dongle when I run a custom BLE connection test repeatedly. Below is my configuration:
FW in nRF52840 was programmed using...
Hi,
I'm learing how the i2s streaming works using the example "echo" under "ncs\v2.3.0\zephyr\samples\drivers\i2s\echo". I have a prototype board with nRF5340 and the audio...
Hi.
I am using a custom board on an nRF52810 microcontroller and a LIS2DH12 accelerometer connected to it via SPI. SDK version 2.7.0.
Here's my settings:
.dts file ...
When flashing the chip with a build from the samples/bluetooth/hci_uart via west build -b nrf52840dk/nrf52840 samples/bluetooth/hci_uart --pristine and west flash off the...
Hello Nordic! My question probably a simple one but I'm a novice so there's it. I'm looking for a way to get a GPIO port state that was at the moment of GPIOTE event triggering...
Hi,
Is it true that you can not disable the nRESET pin in any way? (So that the MCU does not reset after nRESET being pulled low.)
I've gone through the documentation...
Hi Team,
We are using SDK 2.5.2 with MFW 1.3.5
We need to download a secure file from amazon, we first tried to download file from public server connecting to port 80...
Hi DevZone,
My customer found that when using the NRF5340 PDM, there is significant attenuation if the incoming audio signal is a 2kHz signal.
Upon checking the specifications...
Hi DevZone! I am developing a Bluetooth beacon that needs to use extended advertising due to the need of periodic advertising. I am using custom board with nrf52820, nRF Connect...
