Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
My team was looking to transfer a 20-byte value (or 'message') between a mesh client and server, what is the best way to achieve this? I have practiced with the light_switch...
Hi,
I am currently developing an application for the NRF52840 using a custom pcb powered through the VDDH pin using a 4.2v lithium ion battery. Part of my application requires...
Hi,
I am trying to following the instructions at: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.iotsdk.v0.9.0%2Fiot_sdk_user_guides_java_coaps...
I have configured the dev kit by cutting the SB9 bridge. I am powering the device from the J2 USB port on the DK. I have not bridged SB12 or SB11 as I am powering the device...
Hello all,
I am experiencing a ~5uA oscillation (between 5uA and 10uA) in sleep mode, DC/DC converter enabled, no RAM retention. The total current is of the entire system...
i am working with jlink segger edu, in a custom board, it dont have swd TX, RX pins connected, only jtag pins. I Need to see if my gps conected throw uart is working or not...
I configured the pca63519-sr3_nrf52832_shield to fit on my board (actually disabled all peripherals, only the bluetooth protocol part), but found that the modified code could...
Hello! I wrote about the details in topic 66156 , but they did not answer me, because this question is already different from the original one. The drv_rtc.c library has this...
HI,
I have been facing a few issues with the BLE custom service, I am looking to create a Pedo meter service which displays step count information received from the sensor...
Hi Guys,
We have designed a custom board which is using BMD350.
Our application requires using the BMD350 in beacon mode and then going to sleep in low power.
We have...
I can listen for radio inactive event according to this post https://devzone.nordicsemi.com/f/nordic-q-a/9137/change-advertising-every-time-event but I am scanning at the...
Hi everyone,
I want to assign the DEVICEID to System ID characteristic (which is under Device Information Service). DEVICEID is a 64bit and I found that I could assign this...
Hello,
I am developing a sensor like a beacon. I want to measure the distance from the node. I record the RSSI sample for a few seconds and average it to stabilize the value...
Hi,
Can anyone confirm the advert sent in the attached is not corrupted in anyway? as I seem unable to scan my device with anything other then nRFConnect.
The Bluetooth...
Hello,
I found some some threads on similar questions but none answered mine, so here it is:
I try to use UART between nrf52840 and another chip. When the other chip resets...
