Note: This is related to the following issues:
- https://devzone.nordicsemi.com/f/nordic-q-a/63255/nrf9160-getting-stuck-after-cell-change
- https://devzone.nordicsemi...
Hi, I am Product Manager working for Medical Device Manufacturing company based out of Ireland.
we are in search for a development house / developer who will support us...
I have so many versions of this topic that I now am certain that most of the answers provided are wrong. Since you cannot have so many ways of connecting an external nrf device...
Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
Hi Nordic,
I was porting Nordic freertos hrs example(13.0.0-1) to Nuttx system. I can do advertising, connection establishment and data transfer, but bonding failed. I...
Hi,
We are using development kit NRF51822 in our project ...so plz tell me which version of sdk do i need to use ..and also which version of keil do i need to use for this...
Hello,
I want to make a PWM signal that fires an interrupt at the end of the PWM period. I want to use two CC registers - one for the pulse width and one for the period...
Hi,
we developed design with nRF52840, but we have issues.
Propably we have solution for this issues, but we need test it and we need default hex file in nRF52840 for...
As it stands there is some confusion about licensing the DFU utility code in our systems we are concerned about licensing issues. We are compiling the python to an executable...
1.do I need to write a XX_client.c and XX_server.c myself ? is there a basic model that I can build on it ?
2.I need myself model to send a custom message, how to do that...
Experimental Dimming server example was working fine using SDK MESH3.0 in addition to SDK BT 15.2.
Following upgrade of the SDKs to MESH3.1 and BT15.3, the experimental...
Hi,
Does "ble_app_uart" project can print debug message from "UART" interface? How can I do this job?
PS. My UART Port is at P0.18 (TX) and P0.19(RX).
Thank you, ...
After turning on the power,
I did not connect anything on the board.
but it is about 2.7 volts out of the pin (p0.04).
It was almost zero volts before,
but the output...
In my design the nRF52 is connected to an STM32 host MCU. I connected the UART for data communication and the SWD and RESET pins for programming.
The nRF52 needs to be programmed...
Development Software:
nRF5 SDK v15.2.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware:
nRF52840...
Hello ! I encountered a problem in sending and receiving data from one nrf51 card to another nrf52 card
i use this method in (ble_config.c) to send string data :
void...
Hi everyone,
I am developing a quick evaluation demo for a low-power sensor node which consists of the following steps:
- read a couple of GPIOs
- set advertising...
Hi, we are developing an application using USB with NRF52840. We want to connect to the PMID of our battery charger, which will have either USB voltage or battery voltage...
We are using nRF52832 on original PCB board.
We are trying ADC at single-end input, 10 bit resolution, reference voltage is internal 0.6, gain is 3.
We are using regulator...
