I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Hi,
How to upload and debug application program to the beacon with S110_nRF51822_7.1.0 and bootloader (DFU) using J-LINK? The standard procedure takes into account OTA...
Hello,
I want to detect the advertising data of more then one Beacon with the SDK51 and read the TX_Power for a location-application.
I´m inexperienced in stuff like...
will gazell device fall-back immediately to out-of-sync state upon reaching the max tx attempts even if the sync counter is still less than the set sync lifetime?
thank...
I got a nRF51822 based module and I loaded a slightly modified application based on "ble_app_beacon" example in nRF51 SDK via SWD interface using J-Link. The code has been...
Hello,
I have an application in which a BLE peripheral device will be essentially permanently paired with a client. The client will need to connect infrequently with the...
Hi,
I am trying DFU example on nordic evaluation kit using example on github:
github.com/.../DFU-Bootloader-for-nRF51-Evaluation-Kit
However, while compiling in keil...
SDK 7.2
S130 Alpha 0.9
I'm using the UICR customer register address 0x10001080 to stare a single 32 bit number. The code below is a bit of "brute force" to demonstrate...
Hi
I'm trying to make a new S110 BLE project for my nRF51 DK from "scratch" in Keil 5.14 (New uVision Project -> nRF51422_xxAC) , but every time i try to build the solution...
when I program wechat ble demo to my nrf51422 boards with S310 softdevice in Keil, return error like this "No Algorithm found for: 00000000H - 00007503H; Programming skipped...
Looking in the Keil Packs Installer, there are over a dozen entries for NordicSemiconductor::nRF... - each with its own version number.
So which one actually represents...
Hello
I'm trying to implement a number of different interrupts using the nRF51 DK but I'm having trouble understanding how to use the GPIOTE_IRQHandler function.
Basically...
Hello,
I read a while in this forum and found out it might be a little tricky to get I2C working when using a Softdevice. Is that information still valid or outdated? ...
I 'm using SOFTDEVICE.
Can I choose the BLE and NON_BLE while the applications running?
I want to implement, as below.
When I want to use bluetooth, BLE is run. and...
For a school project we have to develop a beacon system, to easy use different beacons we want to be able to change the major and minor from the beacons with UART communication...
I have seen this forum post: devzone.nordicsemi.com/.../
Which refers to this blog post: devzone.nordicsemi.com/.../
But when I use the Keil Packs Installer, and check...
