Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hi,
I know that the nRF52 Dongle should be able to use printk() to debug. I have used it with the Serial Terminal before and it was working.
However, when I program...
Hi,
I have two nrf9161 dev kits. I have flashed the firmware 2.0.1. Then I flashed the hello_dect example.
Now I always get an error and the program does not start. *...
I have a nrf9151dk with a nrf7002ek shield. The nrf9151dk has the DECT NR+ PHY firmware running on the modem core.
I would like to do Wi-Fi positioning with the nrf9151dk...
I have mistakenly disabled Software Debugger (SWD) and wrote the configuration back to the board. Ever since board can not
(1) Connect and get the configuration data using...
Hi.
When working with certain nRF connect SDK versions 2.x.x (not sure which range) in visual studio code, the build terminal outputs relative file paths when showing warnings...
Previously, I successfully completed and performed OTA flashing, and I haven't made any changes to the DFU-related programs since then. However, recently, I have been unable...
Hi! We have tags based on nrf52840 and nrf52833 in the field, running against a central with a nrf840X dongle.
Recently we have had an inexplicable peak in 'Failed to Encrypt...
For a project i need to use the channel sounding feature of bluetooth. On checking samples on nRF Connect SDK couldn't find any examples. But the Zephyr project is providing...
I have customed my own nrf54l15 board and run peripheral_uart demo successfully. Then I tried to measure its current while running peripheral_uart demo, it was up to almost...
Hi. i am trying to turn ON a LED1 and read its status and then turn ON LED2 based on status of LED1 in nrf52840dk board.
#define led1 28 #define led2 25 #define Button 12...
Action for Loading configuration is bugged. It Exports .overlay file but when Loading it only accepts .json file and it doesn't allow you to change it. Therefore, the file...
I want NRFX_SPIM_EXTENDED_ENABLED to be 0. but for some reason it is set to 1. from my current understanding I conclude that the if case here check weather each node with...
Hi
I used the nrf-esl-bluetooth-2.6-branch example to flash the 5340DK (AP) and 52840DK (Tag). I sent the command esl_c pawr update_pawr 9 0 , and then sent the command...
Hello, I am new to BLE and nrf zephyr programming. I am trying to flash periodic_adv and periodic_sync samples ( https://github.com/nrfconnect/sdk-zephyr/tree/16bcaed54230e3d86aeaf2b2f1d47393967254fd...
Im trying to clear NVS, it gets cleared but then causes device to reboot.
code in question is :
output halts after Erasing NVS flash memory (0x000f8000, size: 24576...
