Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
I have developed a data logger using nrf52832 s112 sdk 17.0.2 (nus service).It logs data upto 1mega Bytes,we have a custom buit android app with which we download the data...
Hello,
I am working on nRF52840 custom board, in that, I was facing issues with sd_softdevice_enable().
When I call the sd_softdevice_enable() it's stuck. Not return from...
Im using SPI interface to read data from https://docs.rs-online.com/7d34/0900766b81327f26.pdf using the D2 opcode.
The opcode starts reading the page from the flash (528...
Hi,
we are not able to see any output in NRF connect APP in FFBM mode with DTM Firmware,
However , on flashing complete firmware, we are able to turn on Beeper in FFBM...
Hello Nordic support,
I have a Zigbee coordinator application which has declared the time cluster as a server. I have a zigbee end device which has a time cluster as a client...
Hello I'm using nRF53 DK on zephyr v1.6.1. I'm now testing the power-saving mode. I tested the system-off example "v1.6.1/zephyr/samples/boards/nrf/system_off" and it works...
Hi,
I am using nrf52810 chip. we are trying multilink with central(1 central and two peripherals connected at a time),one central and one peripheral is fine, but we are...
Works on Huawei P20 Lite (Android v9), Samsung J3 (Android v7.1.1), all IOS phones. Doesn't work on Samsung A50.
Samsung A50 does see the devkit when using the same firmware...
OK, full disclosure - I'm pretty new to the whole nRF Connect/Nordic Semi environment, having had to jump across here after all the issues with silicon availability meant...
I would like to configure GPIOs as compatible = "nordic,nrf-gpio"; in devicetree file.
I did check this topic, but I think that this kind of configuration defeats the whole...
Hi, I'm working on a FreeRTOS (I just start to use it, so I'm a beginner) project in wish we want to use an external 32 MHz crystal. The program has a task that should be...
I want to implement CENTRAL using nRF52810. To implement the central, the softdevice must be s132 but I am not familiar with the softdevice concept. Until now, the softdevice...
Hello,
I closed below case by mistake.
nRF9160 receives garbage data on UART sometimes - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi.com)
As per your...
The Thingy:52 application uses LIS2DH in low power standby mode and the MPU-9250 for advanced motion tracking.
Why machine_learning firmware used LIS2DH sensor instead of...
