Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
I'm working on an nRF5340 based design and using the nRF5240DK to get started.
I would like to have an immutable first stage boot loader, an updatable MCUBoot boot loader...
Are there any suggestions for creating slightly customized versions of the immutable and MCUBoot boot loaders?
Currently I'm using CONFIG_SECURE_BOOT=y & CONFIG_BOOTLOADER_MCUBOOT...
I would like to include the MCUBoot library code into my application so that I can read and validate update images (before restarting the MCU to install them via MCUBoot)...
I have a custom MCUboot boot loader working. Now I'm trying to build an application to be updated by MCUboot. I've added the following to prj.conf:
CONFIG_BOOTLOADER_MCUBOOT...
I am running a NUS at 115200 Baud and it works fine but when I run it at 921600 my BMD 300 triggers a Serial Fault. Is there a trick to get the 921600 to work without flow...
Hi Guys,
I need to connect to a BLE device using NRF52480 using passcode (6 digit pincode)
on Android it works just fine, I attempt to connect and displays the popup...
led 1 is off but p0.13 get 3v output , similarly led 1 is on p0.13 get 0v output, how to change it help me. similar for led 1 to led 4 respectively p0.13 to p0.16.
Hi I am the user of zephyr and nrf connect SDK in ubuntu 20.04. one question about file path in the header file. for instance, the demonstration "nrf/samples/zigbee/light_switch...
Hi, I tried establish a communication between nRF52832 DK(PCA10040) to nRF24L01+ Module with Arduino UNO(via SPI). I used the EnhancedShockburst examples from nRF5 SDK 11...
Hi,
I'm developing a GUI on Qt creator to communicate by USB (send and receive data) with a nRF52840 DK. For that, I want to use the USB CDC ACM module (instead of UART...
Hi everyone, I have some problem with SDK 17, when I try compile it by C++ compiler. Compiler detected many errors, for example:
nrf_fprintf,c problem with va_lista
...
Hey hi,
I am trying to establish communication between ADT7410 and nRF52840 using I2C that is the TWI module.
I have successfully checked the address of the ADT7410 with...
At present, our device products use nrf52840, and the official component package used is V15.2.0. I found that using Bluetooth and other Bluetooth long connections will reset...
I made an own SPI device driver using the SDK's BM280 as a pattern
The result has a strange clock configuration (normally high - should be normally low)
Looking through...
