I have so many versions of this topic that I now am certain that most of the answers provided are wrong. Since you cannot have so many ways of connecting an external nrf device...
Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
I'm having some issues creating multiple LittleFS file systems on a project. This is part of a larger project, so I used the Zephyr LittleFS test code to create a demonstration...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Trying to work thru the dev academy exercise 2 using v3.2.4 SDK. I presume this should work because the readme says must be greater than v2.8.0 for thingy91.
I made all...
We are using the legacy 17.1 nrf sdk with the nrf52840 MCU in tickless idle mode and notice that after about 10.5 minutes the current draw jumps from ~90uA to ~277 uA.
There...
Good morning/afternoon all, I have been working on a BLE air quality monitor using the NRF52810. The first version functioned as expected with the exception of the external...
Hi,
We are working with the nRF54L15 using nRF Connect SDK v2.8.0 and would like to enable the secure boot feature.
However, it appears that the SMP Server sample in...
I'm using put all together 2 sample
a) NUS Uart that is used for the configuration;
b) zephyr/samples/net/opentread/coap Using the nrf5340dk/nrf5340/cpuapp.
The compilation...
Hello,
Step 5.2 of this part of the course has a code example which shows which i2c node to use to control the temperature sensor. In the case of the nRF54l15DK it is...
Hello Nordic team,
We are using an nRF5340 as the host processor, and an nRF9160 module is mounted on top of it. All LTE modem AT commands are sent from nRF5340 to nRF9160...
I'm trying to implement the NRF5340 as an I2C slave. The current answers all show the answer as old to look for a newer answer. Were implementing the NRF5340 as a slave to...
Dear all,
is it planned to update the declaration of conformity of nRF9160 from EN 301 908-13 V13.2.1 to EN 301 908-13 V13.3.1?
EN 301 908-13 V13.2.1 is only valid until...
I am currently working with the Aliro 1.0.0 from nRF Door Lock and Access Control Add-on.
I need to know how to properly configure or set custom data fields for Aliro protocol...
How to prevent storage partition from erase durning MCUBOOT firmware update?
I use Settings with NVS to store data
CONFIG_FLASH_MAP=y
CONFIG_FLASH=y
CONFIG_SETTINGS...
I am attempting to get familiar with the NDEF support on the nRF54L15 DK. After creating a copy of a sample based on the WRITABLE_NDEF_MSG example, I create a build configuration...
Hello Nordic Support Team, I am developing BLE content, where nodes will be periodically uploaded to the gateway.During this interval,the CPU needs to be kept idle, waiting...
