I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hello!
Does anyone know of a library for the I2C LCD 16x2 display? I found the library by lovee, https://devzone.nordicsemi.com/f/nordic-q-a/23401/nrf52832-connect-with...
Hi!
With the nRF Mesh 1.2.0 on Android is only possible to set not group address as publishing address.
For group address happens nothing in the app and the device....
Dear,
I tried the same code on :
https://devzone.nordicsemi.com/f/nordic-q-a/43774/simple-gpio-example---nrf9160-dk/173275#173275
and my code:
The Led1,2,3,4...
I know how to set high power (8dBm) when running a nRF52840 as a peripheral (i.e. sd_ble_gap_tx_power_set(BLE_GAP_TX_POWER_ROLE_ADV, m_advertising.adv_handle, 8) ), but how...
SDK 15.2 API6.1
I am using the ble_app_blinky and ble_app_blinky_c examples and when i connect I see the "Nordic LED Button Service" and inside that i see 2 chracteristics...
Hello all,
In order to optimize my power design, I want to power my sensors though GPIO pin on nrf52832 and toggle the pin when I need to use them.
I have two sensors...
Hi.
I have an experience that I do not understand.
<main>
<timer handler>
"PushSwitch" changed to true when the button was pressed using a switch interrupt...
Dear nordic,
I have a custom board. first time its working fine and i flash the program without any issue. after few days i started to reflash the chip its show some errors...
Hi,
From last couple of months I'm working on NRF52840 chip and designed a battery operated device. I also made 5 prototype boards and I'm happy with the range test, coded...
I see two different issue from Segger ES. The below piece of code work well in debug mode, comparison of array at 2k and it fails at release mode. Wondering what's happening...
As a brief introduction, our research group uses bluetooth advertising to broadcast commands and responses between end devices and 'routers' which are connected to a PC. ...
Hi,
BLE Application on nRF52840 (pca10056) development board is being developed.
Application stopped the advertising to make device non-discoverable.
After that trying...
SDK 15.2, API 6.1
I have 1 firmware and 2 PCB it operates. PCB A was an external crystal and the sdk_config file is setup for the operation. However, PCB B uses internal...
I would like to communicate with and existing product that has the ability to communicate thanks to a UART-Bluetooth module. This module uses a Serial Port Profile and shows...
Hi,
I'm working on a thread network and I have some difficulties to configure the BorderRouter.
I use the BorderRouter V2 rapsberry image from Nordic, I recompile the...
