I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
how to configure uart communication between nrf54l15 and tc334 via uart and i need to control my nora b2 evk leds based on mesage from tc33 using tlv can anyone give me idea...
Dear Nordic team,
Please tell me the theoretical power consumption of the nRF54L15 when using CH—both for the initiator and the reflector.
Best Regards,
Riki Yosh...
nRF91 repeatedly transitions to `+CEREG: 4` approximately every five minutes while roaming on Vodafone Germany
## setup
nrf9151 modem FW: mfw_nrf91x1_2.0.4
current SDK...
SDK: nRF Connect SDK v3.4.0 (TF-M v2.3.0) Board: nRF9151 (seen on both nrf9151dk and a custom nRF9151 board) Config: CONFIG_TFM_PROFILE_TYPE_MINIMAL=y, MCUboot with CONFIG_USE_SEGGER_RTT...
While building the program I get this error message: "DT_N_NODELABEL_cpucell_cpuapp_ipc_shm_trace_REG_IDX_0_VAL_ADDRESSU" As far as I can tell, this error message is releated...
HI ,
I wan to disable the vBus "VBUS is not valid, and the pull-up resistor on D+ is disabled." on nRF54LM20,
I try to write to disconnect usb from PC :
NRF_USBHS...
Hello, In the latest nRF Connect SDK 3.2. , I've been having a few "sysbuild/mcuboot/boards" folder layout issues with nRF54L15DK / nRF5340DK when using external device FLASH...
I'm running into a similar issue to Case ID 304027 with trying to build the nRF Thread coprocessor project for the nRF5340. I'm able to compile the coprocessor project just...
Dear Nordic Team,
I am working on implementing OTA (Over-The-Air) firmware updates over UART on the nRF54L15 platform. I have been following the "Exercise 1 - DFU over UART...
I am writing regarding an issue I am experiencing with two MDBT53V-1M modules (nRF5340) that I have assembled on custom PCBs. Both modules exhibit identical behavior, which...
NCS has a sample showing sending UDP packets over a cellular network, with optional control over the RAI socket options:
https://nrfconnectdocs.nordicsemi.com/ncs/latest...
Hello,
I am debugging a custom board that uses an nRF7002 connected to an nRF54L15. The nRF7002 power-up sequence appears to be working correctly, but the device does not...
Summary: CONFIG_MBEDTLS is force-enabled and won't compile without PSA_CRYPTO, costing ~31 KB of secure RAM for unused functionality
I've just migrated my project from v...
