Google open-sources the firmware needed to build hardware security keys
Google open-sourced today OpenSK, a Rust-based project to aid hardware vendors build hardware security...
I would like to store a simple integer value in the flash write and read after some event. I'm using the mesh example Dimming examples (experimental) in the nRF5 SDK for Mesh...
Hello,
Has there been any success with getting the python bindings for the pc-ble-driver running on openwrt? I've succeeded with the driver itself but not the bindings....
Hi Nordic Team,
In my BLE project I'm creating a Test application which gets all the advertising data from peripheral devices. The complete list of scanned device is received...
Hello all,
According to the documentation and this feedback on a case there is a maximum size for a particular cert before nrf_inbuilt_key_write returns NRF_ENOBUFS . Can...
Hello,
I am using nrf52840 DK, Segger Studio IDE, Win10.
My application is I want to transfer the image from iOS to the DK board.
I am aware of the Image Transfer...
1. Setting the IWindow value smaller than Interval will save power.
2. Setting the Interval and Window values to the same will increase the chances of scanning and being...
Hi,I have been using nrf5340 audio DK Board to access the I2S .I am using SPH0645 mic with that i need to get mic data .I am getting mic data continuously but sure that I...
Hi,
we have npm1300 device on our customized board,
without using any of the regulators, LEDs are not connected.
Gpio 0 and Gpio 4 is connected to main MCU.
when activating...
if you see over here data out line is green and prepuol color is data in line first we are sending the 9F so that it will give the manufacture id like this ef and 40 and 0x16...
Hello Support-Team! We are designing a system, where we need to maintain some settings using shell commands (we plan to develop our own set of customised commands). Our platform...
Hi !
Regarding the dfu upgrade service of thingy52, I would like to ask if it is possible to use some Bluetooth devices (such as laird's bl654) to make thingy52 enter dfu...
Hello,I program with nrf52833,NCS v2.9.0.And there is an error happened.
In my main() ,if I place settings_load() at top, it will make my sys resetting. Cause I need to...
Hi everyone,
I’m working with an nRF52840-based device that communicates with an Android app via BLE. I’d like to know if it’s possible to use the nRF21540 RF FEM to extend...
We are looking to do DFU over UART to the Application as described in DevAcademy nRF Connect SDK Intermediate, Lesson 8, Exercise 1, Step 5. However, we have only one UART...
Hello,
I am working on a custom Agora board that includes a BT40 module with an nRF5340 MCU. I am trying to enable the MCUboot bootloader by setting CONFIG_BOOTLOADER_MCUBOOT...
Hello ,
I am getting "Configure Cmake Option visibility" notification in visual studio. I am attaching snapshot as below.
/resized-image/__size/640x480/__key/communityserver...
Hi,
I have just acquired a new nRF52 DK devkit.
Performing a `nrfjprog --recover` followed by `nrfjprog --eraseall` doesn't work to remove the protection.
I do not flash...
Hi,
I use the secure BLE Bootloader to update the nRF52840 (with S140).
Now I want to add a UARTE to update the STM32 connected to nRF52.
Do you have a solution to do...
Hello,
I am using two nrf52840 DKs to test ble transmission and i2s output. The nRF Connect SDK I use is v2.6.0.
Both of them are ble connected. One sends data to the...
Hello,
I think llpm's sample project is wrong. Evaluation board is not supposed to be communicating.
To verify the defect, the value of the time variable is fixed. This...
