Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
I just wanted to share this in case someone else runs into this as well. I was running into all of the same things as others where I could run the nrf_sniffer_ble.sh --extcap...
where can i find some simple examples that transmit / receivfe packets using the RADIO....
assume for the moment that i'll be implementing my own proprietary protocol atop...
Hello, I am trying to develop a 1000 Hz wireless gaming mouse. The mouse has a NRF52832 onboard and the dongle has a NRF52820 on it. (Cannot switch to 52840) I do know about...
Hello,
We have a custom PCB that includes an nRF9160 and nRF7000. We’re planning a hardware update to add external flash memory and would like to know if we can use the...
I'm currently working on a matter application on a custom board in NCS 2.9.0. In the documentation for the ipc_radio net core image the README at nrf/applications/ipc_radio...
Hi all,
I am trying to configure the NFC Pins for usage in an SPI application. However they do not even work for a simple nrf_gpio_pin_set after configuring them with nrf_gpio_cfg_output...
Hi
I have developed a PCB that will be used to control some sensors. The pins NFC1 and NFC2 are intended to be used as GPIOs. However, the default processor settings configure...
Are there any ways/workarounds/configurations to drive P0.9 on nrf52840 as an Input/Output instead of just being NFC pin.
Technically we should be able to drive this pin...
Hi,
I'm using an ISP2053 (nrf5340) chip on a custom board and debugging using the nrf5340dk. I'd like to use P0.02, P0.03 as part of an SPI bus.
I set up a simple experiment...
Hello everyone,
I've recently migrated a code from nRF51822 to nRF52832, thus I started using fds library to manage flash storage from SDK v17.1.
The issue I'm having...
So i have a custom nrf52840 board that i'm working on with SDK 15.2
I want to use the NFC as GPIO.
According to the docs i need to set in the sdk_config.h CONFIG_NFCT_PINS_AS_GPIOS...
Hi,
I'm developing an Android app that will be used on Samsung Galaxy Tab devices only in which the user can connect, through BLE, to another device, which is a module added...
Hi
We have a product that uses a nRF5x Soc. Is acts as both a central and peripheral. The central part connects to a pulseoxymeter, and the peripheral part allows an app...
Dear Developers,
I am in the process of implementing the nRF9151 and would like to inquire about the necessity of the blind vias in its pad. Like on the nRF9151-DK.
Are...
SDK: nRF Connect SDK 2.9.0 with VS Code
SoC: nRF52840. nRF52840-DK for development.
We are currently using USB to output logs for debugging. For production, we disable...
