I thought this should be very simple but it has not turned out that way. I have started with the pc-ble-driver heart rate monitor (peripheral) example. I was able to take...
Hi,
I building a gas meter monitor ( peripheral ) that transmit meter reading to the Central.
The gas meter will be sending to the Central it's ID and meter value ( uint64_t...
The International Conference on Embedded Wireless Systems and Networks will host also this year a dependability competition to benchmark the performance of state-of-the-art...
Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
DeviceTree Visual Editor shows SPI1 as enabled, but the changes are not reflected properly in the GUI or in build behavior.
I receive the following build error : " DT_N_S_soc_S_gpio_50000000...
The nPM2100 datasheet (v1.0) provides Figure 8: Load current triggering mode change vs. VOUT.
Can you confirm:
1. Consider the system is in Low Power mode. If the load...
Hello,
I am trying to implement OTA through BLE, and as Im building the program, Im getting a build error as :
error: 'FLASH_DEVICE_BASE' undeclared (first use in this...
Hello. I have a light sensor connected to 2 gpio pins on nrf5340, Enable Pin : P0.08 and Output Pin: P0.07 Trying to trigger an interrupt based on the light. With the button...
hi support team,
docs says we can program 54l15 external spi flash ,please refer to : https://docs.nordicsemi.com/bundle/nrfutil/page/nrfutil-device/guides/programming_external_memory...
Hi,the Nordic team I'm working on low-power devices that Matter over threads by nrf54l15,I found a problem at present. I interrupted the configuration of the two PIR input...
Hi all,
I’m working on an nRF5340 project where the network core runs a hci_ipc firmware to forward HCI RAW packets to the application core, which then parses vendor-specific...
Hello DevZone!
All samples with Application Event Manager (CAF, nRF Desktop) has simple main function like that:
Main thread has terminated after executing and main...
Dear reader,
I am currently working on a project involving the NRF54L15 microcontroller. In the specifications of the MCU, under Circuit Configuration 1 for QFN48 (QFAA...
Hi I’m looking for some advice on what may be drawing power from the thingy 91x.
I have measured the power consumption of the nrf91 the nRF 5340 and the nRF 7002 using the...
I want to use P0.13 for ADC reading. However, I noticed that it is already used as an SCK pin in this configuration:
spi3_default: spi3_default { group1 { psels = <NRF_PSEL...
Hi!
I’m currently setting up multi-image DFU on the nRF5340 using external flash.
By following the official documentation and samples, I managed to get it working correctly...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
I'm getting timeout errors when trying to program a Thingy:91 with a J-Link Pro PoE on macOS on an ARM Apple M3 Max.
Here's the command and error message:
I get the...
Hi, can you please help me with configuring ras_initiator for channel sounding when using two antennas on the initiator and one antenna on the reflector ? I am starting from...
