Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I am using the following to extract the Device_Name from an advertised packet received on an Arduino Primo:
peer.getFieldInAdvPck(BLE_GAP_AD_TYPE_COMPLETE_LOCAL_NAME, advertisedName...
Hi!
I have a question about the Mesh SDK. Is it currently possible to get the physical source of a relayed message (thus the relay that send it) out of it? I only seem...
I use buttonless_dfu_app as template. SDK 14.2
Q1. Could someone help me.. After I updated my app I have changed crc (if more than just few changes), so bootloader installed...
I made all steps in a guide
devzone.nordicsemi.com/.../
All works fine. After that prepare my own firmware like appendix 1. Also works good. I merge
bootloader_setting...
Hello,
i'm trying to run the ble_uart_example on my nRF52840 eval-board, but it always fails on this line:
err_code = ble_advertising_init(&m_advertising, &init);
APP_ERROR_CHECK...
Hi, everyone,
I develope the project with BLE support. In my project I need to define the time server. For this purpose I tried to find any example reffered to it, but no...
It is a sensing-processing-actuation based application. Just want to use the nRF52832 module for BLE communication( a part of the application).
Is there a direct API in the...
Hello,
I have an application where an nRF52832 peripheral (S132 v3.1.0) transmits a 5-to-10 MB file to an nRF52832 central (S132 v4.0.5). The peripheral sends the file...
Hello,
I have bought an nRF51 dongle with a SEGGER J-Link.
I have downloaded all the SDK and everything from nordic website.
If i open an ble peripheral example in uvision5...
Hello i cannot get uart to work correctly on these pins. The board seems to reset when i try to run uart on these pins. I can get them to work on pins P0.06 and P0.08. I think...
I could not find update info on this;
When I use mergehex to combine SD, app and bootloader, MCU just boots into DFU mode.
When I program SD, bootloader and app, MCU...
I have a nrf52832 running as a BTLE peripheral running up a couple of services including one custom with a characteristic i wish to be modified by the peer.
Data is being...
Now I'm using NRF52832 to communicate with other MCU(STM32) by UART.
STM32 will transmits about 40 bytes data to NRF52832 per 10ms.
Here is my configure referenced Nordic...
Are there any dependencies between the connection parameters configuration and pairing?
I am using nRF52840 and SDK 14.0.2 and ATT_MTU example. I am trying to add pairing...
