Hello, i intsalled the software stack for use with latest release of nrf sniffer package.
By starting the capture process with wireshark 3.2 i have noticed an issue:
In...
I have a project where we have 2 nrf51 that need to be time synced with eachother.
The problem is they are placed on the body one on the back and one on the chest of a person...
on the page
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v16.0.0%2Flib_crypto_backend_micro_ecc.html&anchor=lib_crypto_backend_micro_ecc_install
step...
Hi,
In our one of the product we are using Nordic nRF52840 MCU and we compiling this application code in windows with SEGGER Embedded STUDIO IDE Version 4.30a and Tool chain...
Hi,
We made an online course on Bluetooth Low Energy, includes BLE Fundamentals & Architecture, step by step implementation of Environment Sensing service development...
Hello, I am using nRF9160 PCA10090 DK. I want to make my board as central device and scan for all nearby BLE devices and display its rrsi value and device id on a terminal...
I can read above 3000 samples from accelerometer, before connecting to BLE, but after connecting to BLE the data rate reduces to 200 samples. This is clearly checked and identified...
I have been using VS Code and nRF Connect extensions for over 1 year. I run on a Mac Mini computer with Apple M2 processor. I recently updated the macOS to Sequoia Version...
I'm trying to build my project for nRF54L15 DK. The project uses mcuboot. When mcuboot is being built, I get following warning:
I guess the problem is caused by the config...
Hi, DevZone,
Our customer, Hosiden Osaka, wants to get the recommened foot print regarding nRF54L15, that is, the following each land pattern respectively;
- WLCSP 300um...
I am writing a program for the nRF52805 for use in a battery-operated remote. It needs to wake up from sleep when any button is pressed, perform the interrupt (blinking an...
I have found that in NCS SDK 2.6.2 it was very simple to enable FLASH_SIMULATOR as part of the mcuboot configuration overlays. But starting from SDK 2.7.0, I keep getting...
Hello.
I found this in the sx126x .c driver :
These lines did not allow adding more than one device to the overlay . I removed this code and rewrote all driver files...
example Matter_light_switch in vs code
version using nrf connect sdk -> v2.8.0
manage tool-chain version v2.8.0
nrf52840dk
getting error while building code
...
Hi,
I follow the execise https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-8-bootloaders-and-dfu-fota/topic/device-firmware-update-dfu-essentials...
Hi,
I'm trying to find the BOM referenced in the Hardware Design Guidelines for the nRF9151 under the Schematic Design section. According to the document, the BOM should...
Is there a way to obtain the Tx/Rx packets num in LE Audio? I want to calculate the PER in LE Audio. Using nrf v2.60, NRF 5340 Audio DK.
Thanks for your reply.
When configuration options CONFIG_SEGGER_SYSTEMVIEW =y and CONFIG_TRACING =y are added to my prj.conf the following build errors are shown:
followed by many other errors...
Hi,
I have a NRF52840 DK , I was using it for development. After one day the board don't turn ON anymore. I'm using USB cable as a power source. Acording to several subject...
Hi:
I use ncs v2.8.0, using external flash(w25q128).
this is test flash project.
And this log:
Device_is_read returns a failure. But flash read/write successful...
I'm encountering an issue with the use of the GPIO interrupt type GPIO_INT_EDGE_BOTH on a GPIO connected to a button. When pressed, the button pulls the GPIO to GND, and when...
