Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
We are developing a USB ANT dongle with nRF24AP2-USB chipset, but we meet a problem when use CW test with ATWareII tool.
We set 2.466GHZ, but we see 2.271GHZ mark, but...
Hello,
My code( I add a source code lower ) has error on bold line printing NRF_ERROR_INVALID_STATE. The program uses three timers and init by "MAX_TIMERS = 6" and "OP_QUEUE_SIZE...
Do anyone ever measured current consumption of ble_app_uart?
What is current when connected and uart idle, transmitting, receiving, and transmitting while receiving?
Please...
I tried changing the define below from 1 to 2, so I could have one handler for a button and a different handler for other sensors. But my problem is:
If I set it to...
Hello,
I've developed a circuit with Mikroelektronika's nRF T click module. This module uses nRF24L01P but as I see I cannot order it because it is obsolete.
Should...
We plan on use the ST BAL-NRF01D3 balun for a PCB with both an nRF51822 and a nRF51922 on the same PCB separated by about 4 inches.
Should we use the PCB antenna as on...
Hello.
I am very confused with memory layout of nrf51822 BLE examples using SoftDevice stack.
Some examples set IROM1 range from 0x0 to 0x3ffff. (ex, ble_app_advertiseing...
Hi,
I have a nRF51422-EK board (Rev. 1.0) that is bricked.
When connected the LD3 is on.
Jumpers are present on P8 and debugger.
Device manager (win7) assigns...
Hello,
I was puzzled by RM.
I notice POWER control register in peripheral(UART,SPI,TWI) module.
Please answer following questions about the relation between system...
I download the softdevice for PCA10001. And I want download another program, but it didn,t work. The problem I have attached here. As you known, I have push the button 'recover...
We plan on using the external 16 MHz and 32 KHz oscillator inputs to reduce BOM costs since our host micro uses a 16 MHz and 32kHz crystal and it can generate outputs. If...
Hi guy:
I have buy nrf51822 dk .Why I can not download nRF UART App for Android 4.3 at below page www.nordicsemi.com/.../nRF-UART-2.0-for-Android-4.3
Thx
I made code like to below for using 16Mhz system clock.
/* Start 16 MHz crystal oscillator */
NRF_CLOCK->EVENTS_HFCLKSTARTED = 0; NRF_CLOCK->TASKS_HFCLKSTART = 1;
...
