Hello.
I need some advice - I'm a beginner. I tested the transition to sleep mode via __WFI for the nrf52840 Dongle (VS code, SDK v3.3.0). I need some advice - I'm a beginner...
Hi all — I'm developing a custom nRF5340 development board (Raytac MDBT53-1M) and would value the community's honest read on whether it's worth producing.
The goal is...
Hello,
I'm having trouble saving signing keys to the KMU on the nRF54LM20-DK.
I'm using the build for the nRF54LM20B, as recommended here, so the KMU should be used for...
Hi
my project is about live streaming of physiological data at high sampling rates over BLE.
On the receiver side I have a Laptop(Windows/Mac/Linux) and not a NRF dongle...
Hi,
I am using two nRF52833 devices with the nRF5 SDK. They are paired and bonded to each other. Occasionally, I encounter the following error in peer_manager_handler :...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
Hi,
I use the nrf mesh sdk for long time and I just see that its migrate to zephyr rtos.
After reading the nrf mesh sdk doc and the zephyr project doc, I have some questions...
Good afternoon.
We're using nrf Connect for mobile to perform DFU over BLE to an nrf5340-based module with firmware built using the nrf connect 1.6.1 SDK and its associated...
0 dBm TX @ 1 Mb/s Bluetooth Low Energy mode, Clock = HFXO 7.1 mA
Radio RX @ 1 Mb/s Bluetooth Low Energy mode, Clock = HFXO 6.5 mA
I want to know which example is tested...
The CAN controller MCP2515 should be connected to the Nordic DK NRF5340 by the SPI interface.
Communicate to Arduino uno
We were trying with CAN sample given
But this...
Hello,
I've tried to request the location via AGPS/PGPS via Location sample in SDK 1.8 but it seems that location is only working with the Cellular method.
I've tried...
Hello there, I am new to your product, and I am trying to understand your library logic and hierarchy. Right now I am trying to figure out what all of these prefix (such as...
Hi, I want to use an NRF52805 with a voltage to frequency detector. If I understand the datasheet, there is one timer/counter and RTC on that chip. Is it possible to set the...
Hello,
How do I deactivate/activate a SDA/SCL line?
I perform a test on an Icarus board with a VL53L1X sensor, everything works fine.
However, in idle/sleep mode, whether...
Hi,
I am unable to view the output of the prink statement on the SES debug terminal. I'm a beginner so please bear with my lack of knowledge.
Should I be looking for the...
I am trying to adapt the zigbee light_bulb sample to run on nrf52840-Dongle which does not have a QSPI flash chip. I see that it crashes unexpectedly during settings_subsys_init...
Hello,
We have product with nRF52811 as Bluetooth receiver and ESP32 as WiFi IC. The ICs have separate antennas, and nRF52811 has LNA with +12 dBm gain connected to antenna...
https://github.com/project-chip/connectedhomeip/blob/master/docs/guides/nrfconnect_examples_cli.md
uart:~$ clear date device devmem flash help history hwinfo kernel nrf_clock_control...
I have loaded up the altium design and can see the pad and via sizes used.
The drill size for the in pad via is very small (0.15mm) which will increase pcb costs and also...
*** Booting Zephyr OS build v2.7.99-ncs1 ***
nrf52840dk_nrf52840 system off demo Retained data not supported Busy-wait 2 s Busy-wait 2 s with UART off Sleep 2 s Sleep 2...
Hi,
Installed the toolchain, installed VS Code, and I think its all linked, but when I try to run even the most basic hello world program it just keeps throwing this error...
