Hello together,
i am trying to connect to an Azure Blob Storage Container via https with a nrf9160 but I am only getting error 111 (connection refused). For that I am...
Dear Support,
I'm using nCS v3.1.1 and the Matter example project. Could you please provide a simple example showing how to use GPIOTE + DPPI + TIMER capture?
My goal...
Hi,
I am using two nRF52833 devices with the nRF5 SDK. They are paired and bonded to each other. Occasionally, I encounter the following error in peer_manager_handler :...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
Hi,
I've been using NRF Cloud without issues (Pro subscription) and I am no longer able to login my NRF Cloud account. I tried changing password and use different type of...
I am trying to do some power measurements on the nRF5340 using the power profiler.
As suggested in the guide here, I am removing serial support to reduce power consumption...
Provide your AWS credentials page for Asset Tracker Cloud Example for AWS mentions sub-accounts. There is absolutely no such thing as a sub-account in AWS. The page is totally...
Hi.
I've been working with the nRF52840 for a couple of months. I started working on SEGGER IDE, but I've found that it was quite difficult to understand the behavior of...
I played around with the SAADC sampling A4 pin. When I connect to GND, I see negative values sometimes. If I connect to 3.3V I see value 235/236 which is, what I expect. ...
I have 2 device gateway and nrf52840 board.
Can i get zigbee distance?? I think RSSI data is possible. Right??
If you can measure the distance between gateway and nrf52840...
Hello,
I am using nRF52833, nRF Connect SDK v1.4.2.
I have imported the Zigbee light switch, light bulb, network_coordinator build and test it successfully.
I have also...
I should not be asking this question here but it should be documented! SoftDevice s130.
A possible error I can get when executing sd_mutex_acquire() is NRF_ERROR_SOC_MUTEX_ALREADY_TAKEN...
Hi All,
Hardware: Custom Board (Buttonless)
SDK : 17.0.2
SD: 7.2.0
Support required: DFU Buttonless
We are able to successfully load and run the DFU buttonless...
I am using nRF52832.
Can I use NFC1/P0.09 as SCL and NFC2/P0.10 as SDA?
nRF52832_PS_v1.4.pdf states "The pin capacitance will be higher on these pins" in 4.3.2.
I am...
I posted one question in my earlier ticket about download firmware to our own device (nRF9160) through DK of NRF9160.
Now we are design the schematic of our own device with...
Dear Concern,
I am getting MCUboot build errors as shown in the below.
C:\Nordic\v1.5.0>west build -b nrf5340dk_nrf5340_cpuapp -d build_mcuboot bootloader/mcuboot...
Hi,
I have nrF52840 DK rev 2.0.1
switch to VDD, Default, SB40 is cut (confirmed by multimeter)
I have the PPK rev 1.1.1
switch DUT to DK
switch Power to DK
I...
Hi,
is possible use for DFU process as DFU server other device as development kit?
I will use it in street lighting but it not usable with development kit. I would use...
I have a couple of examples that work ok on 9160-dk and use SPI3.
However, if I try to use these on SPI1 or SPI2 I get a device not found error.
I am building with west...
hi,
i am working on timer example in peripheral folder. i am including this example in ble_uart example in ble_peripheral folder. i am getting error " 'NRFX_TIMER0_INST_IDX...
