Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi,
I recently procured a nrRF52 DK board (PCA10040, v2.0.0 with nRF52832) for our new product development activity.
I tried following precompiled binaries present in...
Dear Nordic Tech Support & community,
The SDK 16.0.0 supports only one button long-push at time. Attached you can find a SDK-patch to add the support of multiple long-press...
Hi Team
I am trying to implement the firmware upgrade for master controller nrf52832 on chip using esp8266 over uart and I am very new with this boot-loader part.
I...
Hi
I had implemented a DFU module in esp8266 where I am trying to upgrade nrf over serial (UART Communication).
I had success with Init file write but when I send the...
Hi,
I am using nrf52833 EVB as an SPI master. The data is sent properly and well-received at the slave, however, I have a problem with the data received.
The problem...
Behaviour:
- Bluefruit the feater (nRF82832)
- Bluetooth BLE
- Implementation of Fitness Machine Service (0x1826)
- What is correct : all characteristics notified...
Hello, Nordic!
Our project is at evaluation stage. We aimed to build an Bluetooth 5.1 AoA indoor locator system, where the reciever should know the location of the transmitter...
We are using nrf52840 USB dongle to get PIR sensor readings and send measurements over the Bluetooth Mesh Schematics are following: We increased power for peripherals to 3...
Hi:
When I use nRF51822's 2.4G Radio(not BLE),I want to improve anti-interference level,Make sure that all my pairs of host and device can communicate normally.
Thank...
Hi
Looking at the AGPS sample code, it seems GPS/LTE is turned on and off using AT commands (AT+CFUN=x, x in {20, 21, 31}).
Do you recommend NOT using PSM when using AGPS...
Hello,
I have several nrf52 Development Kits which will be used for creating a Bluetooth mesh network. They sport the NRF52832 SoC.
Do they have, or will ever have, support...
Hello
*Environment
- LG V30 (Android 9)
- nRF52832, 15.3.0 SDK, S132
- nRF5340 ( I can't find SDK version)
I have some issue.
LG V30 Mobile can't reconnect...
Hi,
I am using nRF52840 USB dongle and DFU trigger library to update firmware without push any button.
The Python 2.7.x is working fine for DFU trigger into the DFU mode...
Hi!
I am developing a iot solution and I wanna send sensors data to broker by MQTT publisher. In my code already has the W5100 development and now I want to connect my device...
Hello,
I would like to create a new box in the nRF cloud for recording additional data. I know these boxes allow exporting the recorded data into a CSV file, which is ultimately...
