Hi everyone,
just a quick tip that may save you some debugging time when using the nRF Connect SDK Build Configuration Editor (both in VS Code and standalone):
If you...
If I try to compile any of the WIFI examples for the Thingy91x I get a RAM overflow error. The only exception to this is the WIFI scanning example. If I build these for any...
Hi everyone,
We’re currently using the nRF9160 module with JIO Nb-IoT SIMs in our devices. Could anyone clarify if any specific actions are needed in the firmware for...
Hi, I was using the BLE online power profiler to determine possible power savings with the nRF54L15DK over the nRF52840 using the zephyr bluetooth broadcaster sample. The...
Hi!
I have been unable to find a single, simple set of instructions for adding MCUboot to a project(toolchain 3.0.0 sdk 3.0.0) that will enable a non-default signing key...
Hi, I am using ncs 3.0.2 and an looking at adding extra .conf files during production. For the app it works fine using --extra-conf, but I can't figure out how to add one...
hello again,
i spent the last three days on the theme dfu, bl, app, sd. Now there are some questions I can't answer me with reading.
Question 1) Does a new app works ...
Hello!
In our design we need BLE 5 solution with maximum allowable by reulation +20 dBm TX power. It is not a problem to use a separate PA for achieving that power, however...
Unable to obtain repeatable scan response data.
I can obtain advertising data and scan response data from 3rd party devices. I can obtain advertising data from my server...
When initializing models from the models_init_cb it's useful to check the current configuration using the mesh config API. However, the returned values are always the default...
We are testing GPS capabilities for our hardware, using mfw 1.1.0 in the field. We have the following test conditions
The unit is ackquiring position every 5 min
the...
Hello,
We are trying to run the ble_ant_app_hrm example on nRF52840DK using nRF5_SDK_16.0.0_98a08e2 SDK and ANT_s340_nrf52840_6.1.1 softdevices (both latest as of today...
Hi,
I was looking for information about the MLME-ASSOCIATE primitives in the https://infocenter.nordicsemi.com/ . The section with the "MAC MLME Association API" title...
Hello. After I updated the firmware on Thingy 91, it no longer registers on the network via LTE - the LTE indicator in LTE monitor blinks between yellow and red, and I get...
Hello Nordic team,
I was wondering how to determine the QDID of our product. The relevant QDIDs are 101625 and 97989. I believe the latter should suffice but I am not sure...
Sir After Flash the code to board i am getting some info message in teraterm
below i have attached the image of the teraterm
Refereed link: https://infocenter.nordicsemi...
Hello Nordic team,
I'm using an nRF52840 with SoftDevice S140 version 6.1.1 which size is 0x25000 (without MBR).
My bootloader contains the bootloader code written at...
Hi to all,
Happy New Year 2020 !
I have developped an application with the nRF52832 ( nRF52DK ) and I use the SAADC for battery level every 2 hours ( no need of precision...
Using a NRF52840 running zephyr and mcuboot, the function nrf_cc310_bl_ecdsa_verify_secp256r1() is getting stuck in a loop.
I am using NRFXLIB v1.1.0
Looking at the disassembly...
Hello,
we developed 3 devices using nrF52840 and integrating your certified Zigbee stack.
in order to obtain the Zigbee Alliance certification, the laboratory ask us to...
hi , i need help!
when i conected to the phone(bonding),then i disconnect from the device using sd_ble_gap_disconnect(),next the device advitising again; after that the...