Hi everyone,
I'm working on a project using the nRF54L05 (v2.9.0) and I'm currently facing an issue with BLE. I want to change the BLE transmit power , and so far I’ve only...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Are there any migration guides for a customer who wants to migrate from nRF5340 to nRF54L15? And if they are nRF54L15 in chipscale, anything they should be aware of including...
Hi,
I have been playing around with the configs but I could not get Mode-3 to activate. What should I change for cs configs and the prj.conf file in order to activate it...
nRF52832 & nRF52810 don't support the Bluetooth 5 Range Extension (Coded PHY):
https://devzone.nordicsemi.com/f/nordic-q-a/39532/is-it-only-nrf52840-s140-which-support-bt5...
Whenever I deploy an example to the Fanstel BT840F with Segger ES, the S132 SoftDevice is always also deployed to it. I have attempted to change references to this in the...
Hi,
nrfx_uart.c has a bug where, once there is a RX error, the receiver gets stuck in a disabled state forever. This is because p_cb->rx_enabled is never set true, so the...
hi, my name is tyto I just learned programming about nrf52832, before I used to work with Arduino, after trying to learn nrf52832, it turned out to be very difficult for me...
Hi,
I'am using SDK v15.0.0 with the BLE OTA DFU bootloader. Is there a possibility to access the bootloader start address for a static assert in the application at compile...
We have bought nrf52 832 development kit.
When we checking the kit in nrf52 utility than it detects the IC nrf52 840 .
Hence we have erased all the memory in the DK...
Hi everyone,
I am using the following files to configure uart for laser distance sensor.
Serial Library
I am able to write command to the Laser sensor and also the laser...
Hi,
As far as I understand from this page [https://openthread.io/platforms Host / 802.15.4 Controller section] it is possible to have Dongle running thread attached to PC...
Hi, everyone,
We develope project on nRF52832 Chip. It has one UART port and we need to make it working as RS485. For this purpose we connected to TX/RX pins the required...
I am trying to send hundreds bytes to peripheral, the best tool that I can find, is still nrfConnec. But the data only be typed one by one. Is there any way let it load a...
I am using a nrf52832 with SDK 15.2 and softdevice s132 v6.1
My peripharal should transmit an iBeacon to wake up an application on the smartphone and also transmit a connectable...
Hello,
For a new project I am using the Decawave module DWM1001. This module is equipped with an NRF52832. I have already used the nrf52832 for previous project and I face...
Hi there,
Is there a specific sequence needed to power-up the NRF52840?
Let me get into the details:
My design uses configuration #5 from the datasheet (see below...
