I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
HI ALL,
I want to obtain the status of the upgrade process using mcuboot ble, such as flashing lights when starting the upgrade, flashing lights during the upgrade, and...
Hi,
I am working with the nRF54L15 and I want to use it both as a BLE central and as a BLE peripheral. So, I have two separate source files: one for central and one for...
Hi all,
nrf54l15dk,v3.0.1,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
Finally...
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
Hi
Our present build system on v2.6.1, builds variants of our baseline application using batch files.
It ends up building using west in this way:
The generated...
Hi,Team,
I am developing pawr using nrf54l15-dk. I wanted to set the parameters of pawr with 128 sub-events and 8 response intervals, but the setting Failed and the error...
In the main function, this works.
Works ..
Not works , I got NRF_DRV_TWI_EVT_DATA_NACK error..
and I cannot call "nrf_drv_twi_tx" in the timer event handler...
Hi everyone, I am testing out the qspi flash on pca10056. While the read speed is decent around 650 KBs, the write speed is too slow ~ 35 KBs. It could be our own usb/caching...
There is an example in the SDK v15 folder. " ble_app_buttonless_dfu "
I write a custom firmware which has ble interface sending temperature data.
I want to add ble bootloader...
Hi,
I'm using the S132 v6.0 and SDK v15.0 to work with nRF52832. I found the it just get the advertising data. If the device put some data into the scan response, when I...
Hi,
I want to use nRF52840 USB dongle in my setup with other PCA10056 boards. I have seen that in link https://www.nordicsemi.com/eng/Products/nRF52840-Dongle it is mentioned...
Need to upgrade bootloader by application code. I have finished to program bootloader image to FLASH. Content is verified correct, comparing to SRC. However, the bootloader...
I have 2 52840 modules with PCB antenna and I am trying to check the max connection range
I followed the recommendations and achieved only 120m.
I cannot use the examples...
Hi, we recently using audio with ATVV service instead of HID service. As we notice, Audio would enable by SR3 itself in ATVV service if we push the key, but not in HID service...
Hi Nordic:
I want to change TX power of mesh-sdk.2.1.1 light switch, I've follow
https://devzone.nordicsemi.com/f/nordic-q-a/34491/mesh-range-power-and-mode
and set...
Hi,
I have bougth one Nordic Thingy 52 and one nRF52840-DK. My idea is to communicate both via bluetotth.
For example, i want to capture the temperature adquired by Nordic...
Hi guys,
I am using the softdevice S120 firmware: s120_nrf51822_1.0.0-1.alpha_softdevice.hex
The error_handler registered when calling sd_softdevice_enable is called...
We are implementing a Nordic NFR52832 using the ARM mbed ble stack that leverages the Nordic SDK using a HID over GATT profile. Windows 10 seems to have an issue with this...
Hi all.
I'm trying to make a list of brands and models of Android phones that have implemented LESC. I appreciate any feedback and experiences working with LESC (numeric...
Hi There,
I just want to confirm which method is being used to perform DFU over thread (Single bank update or dual bank update), and can I perform DFU on Sleepy end device...
Hi,
I'm trying connect NRF 52840 width Intel AC 9260 Windows 10 Desktop/
When I compile and run any examples from nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral and I...
