Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
I am using nrf52832 to develop based on SDK14.2. I have defined a custom service . There are 7 characteristic in this service. The attribute of each characteristic is set...
When broadcasting mesh messages I use the access_reliable_t struct to set data.
I need clarification on what the contents indicate. The documentation is sparse and doesn...
I'm trying to model up current consumption of our system. I'm looking to put the nRF52840 into System OFF, no RAM, Normal voltage mode and waking up on both GPIO and USB Detect...
Hi,
Is there a list of the exact part numbers for all the components used in the nRF52832 reference designs? I could only find a pretty general Bill of Materials in the...
I am planning to make a custom board using nrf52832 ,for that i need to know what are all the steps need to be followed to perform OTA DFU to upload a custom firmware . List...
Hi everyone.
I'm working with light switch example in MESH SDK 2.0.1.
I want to provisioner working like a client. Provisioner can send command to another node to on/off...
I have to implement temperature sensor readings continuously through interrupts instead of busy waiting example in SDK in order to notify those values over BLE to cloud. ...
I'm looking to encode and decode an AFSK signal (via wire not RF) using 2KHz (0) & 4KHz (1) with an 8-bit frame size and 6 frames to a block. Is this achievable with the Micro...
hello sir i am designing a custom pcb based on your mcu nrf52832 board
can you help me how to customize it according to my need without disturbing antenna .
USB device don't recognized by system if we try to use more than one endpoint in app_usbd_hid_generic library:
APP_USBD_HID_GENERIC_GLOBAL_DEF(m_app_hid, INTERFACE_NUMBER...
Hello Nordic
I'm using nRF5_SDK_15.0.0_a53641a.
I think I found a bug with the ble_nus.c, line: 96
I think the rx_handles.cccd_handle should be the tx_handles.cccd_handle...
Dear all,
I'm trying to run nimble stack with Nuttx OS on nrf52832(pca10040) reference board. Now , most function is working , but it is not stable .
Sometime , the svc...
Hi,
This function is called after I turn on Bluetooth a while of my project.
What is the cause of this and How can I do to fix it? I can't debug to source code of softdevice...
Hi, We used Nordic SDK12.2 Softdevice3.1 to develop our smartwatch. After launching our product, we got a lot of complains on the connection and re-connection on Samsung Android...
