If I try to compile any of the WIFI examples for the Thingy91x I get a RAM overflow error. The only exception to this is the WIFI scanning example. If I build these for any...
Hi everyone,
We’re currently using the nRF9160 module with JIO Nb-IoT SIMs in our devices. Could anyone clarify if any specific actions are needed in the firmware for...
Hi, I was using the BLE online power profiler to determine possible power savings with the nRF54L15DK over the nRF52840 using the zephyr bluetooth broadcaster sample. The...
Hi All, I am trying to write to "adafruit e-link 2.13 Featherwing colour dispaly" from nRF54L15DK running zephyr. With ESP32 i am able to write to the display. But with nRF54L15DK...
Hi, i am looking for basic start up parameters for a 24L01.
I do all my programm in assembler (sorry i am old).
what i aim to do is simple TX-RX, like a small remote...
We are currently using Zigbee Firmware built with nRF Connect SDK v2.7.0 on the nRF5340.
We plan to upgrade the nRF Connect SDK to v2.9.2 and use the Zigbee Firmware built...
Hi,
i have a wierd behavior on my board.
On my nrf52832 custom board i have sdk14.1 with DEBUG flag and NRF_LOG enabled.
Usualy when my board crash i got into some kind...
Hi.
I have RF communication between nRF24L01 + and nRF24LU1 +.
Incorrect data is transmitted occasionally during communication.
So, I want to use CRC, but when CRC...
I want to get 32000 bytes per second with NRF24LU1+ ,as my audio sampling rate is 16K and sampling bits is 16.But actually I have lost one packet or more per 10ms. data loss...
Hi Everyone,
Is it possible to programmatically assign a static mesh-local EID IPv6 address to a node in a network? I would like to communicate to individual nodes in the...
I am using the nRF52832 Soc, and have a requirement of using a timer with a large timeout value, hence I want to use the watchdog timer.But as I get TIMEOUT interrupt the...
Hello!
I need sensitive gpio.
I want that is gpio rising in 20[nsec].
However, the test results using the function below show that the gpio rise time is 200 nsec...
Hi,
I am new to the BLE environment. I am trying to connect my smart phone with nRF52832 development kit over BLE. Here, my smart phone should be able to send some user...
I am looking to extend the RTC beyond 24 bits using the Overflow interrupt.
The code in the rtc handler would look like:
static void rtc_handler(nrf_drv_rtc_int_type_t...
I have been trying to install the new version of everything Nordic 52.
That starts with the MDK 5.18.
To make sure I don't have an update problem I do a clean install...
Hi,
I want to know about mathematical formula to find / estimate the battery life of Bluetooth beacon containing NRF8240. If chip is transmitting at +8 dBm and have 1000...
Hi,
I add the NUS in the ble_app_hids_mouse example which the sdk version is 14.0.
There are four services in the project: dis, bas, hids and nus.
When I connceted the...
hi all ,
I am looking out theory about SM layer in BLE . I read CoreV5.0 but I do not understand much about pairing , bonding , STK , LTK . Can you give me some document...
Can the link between two devices communicating with each other via NRF24L01+ be improved by using Tx messages with no ack (W_TX_PAYLOAD_NO_ACK) instead of messages with ack...
Specifically, sinking a Cree C503B green LED (Vf 3.2V at 20ma) from a GPIO configured for high drive, without a current limiting resistor, from VDD 3.6V?
Figure 23 “GPIO...