Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
On 52832, SDK V14.0.0, SD132-5.0
I tried to set NRF_SDH_BLE_GATT_MAX_MTU_SIZE to 247, as from dev-doc i saw that SD132 supports BLE V4.2 DLE.
However it returns:
...
I would like to know how to create a prompt that asks for a PIN before a user gets access to pairing to a BLE peripheral. Currently I'm using a CurieBot and once it's found...
Hello.
Using nrf51_8.0.0_API, I'm experiencing the function sd_flash_write returning the value NRF_ERROR_INTERNAL. As documented in nrf_soc.h, this error code can never...
Hi,
I'm working on app based on ATT_MTU Throughput Example from SDK 13.1, but I added Thread support and now working with Thread SDK 0.10.0. I have a problem with advertising...
I have a hard time understanding precisely what an Element is and how it differentiates from a Model when talking Bluetooth Mesh.
The only definition can seem to find of...
Is there any way to detect / prevent the use of range extenders?
When using a central & server with low TX power, the range is say 10m.
Now an attacker can use a relay...
Hi all,
I have been using Nordic chip-sets for a while mainly for BLE applications. I am now developing a simple lighting product based on Nordic nrf51 family chip-set where...
hello!
i am working with the component nrf52840 v0.5.1 and i need development a thermal profile according with the datasheet of the component nrf52840 v0.5.1
could you...
I'm using op-amp(LM358), condenser microphone and PCA 10028.
My project collect output values of op-amp and broadcast that.
But, noise was occurred while it is advertising...
I'm using the ble_app_multilink_central example app.
In the pca10400.h I changed #define BUTTON_PULL to NRF_GPIO_PIN_PULLDOWN.
The problem is that the first pin interrupt...
Hi
I'm creating an android app for smartwatch(used nrf51 ble),I have two questions
1.I used ANCS(Apple notification center service) in my android app,but nrf51 device...
I'm using the SD (nrf52) MBR to update our custom bootloader, in a battery powered device.We have some custom hardware which is used to disable our LDO, to enter a "Ultra...
Hi Everyone,
Recently I have been trying to measure the current consumption from the dev board.
I have set up the board as instructed by cutting SB9 and soldering SB11...
Hi,
I see intermittent incorrect values from the saadc. The code is described here .
The graf shows battery voltage in mV over about 4 days with one sample per minute...