The nrfx pwm supports a number of events for a callback: /** @brief PWM driver event type. */ typedef enum { NRFX_PWM_EVT_FINISHED, ///< Sequence playback finished. NRFX_PWM_EVT_END_SEQ0...
Hi,
I have two nRF5340 DKs and want one to be server, one be client. I use NCS offcial code and simply buide them, however, " LED3 starts blinking green on every device...
Hello,
I have been working with the nRF9160 DK to understand AT commands. I tried flashing the Serial LTE Modem application using the Quick Start option in the nRF Connect...
Hi everyone,
In nRF9160 with ncs 2.9.0 I've problems when trying publish a MQTT payload bigger than 2700 bytes aproximately. In advanced I already was adequated buffer size...
Hi,
I'm working with a fleet of devices using the nRF52840 and NCS 2.6.0. Some of these are older devices with a bootloader that only supports RSA signatures, and I cannot...
Hi, I've recently acquired an nRF54L15DK, and started the development on BLE, I'm fairly new to Nordic's enviroment. In the last couple days I've been trying to build the...
How can I differentiate between a brown-out and an initial power-up on the nRF54L15? In my project, I need to detect a brown-out event in order to trigger specific actions...
I'm working my way through BLE Advertising, a beginner's tutorial and getting a SDK error 4001 when trying to use
advdata.include_appearance =
true;
Can anyone...
Hello!
I'm trying to nRF52 soc chip to drive the matrix sensors array (16x16), because there is no enough I/O pins for my project and thinking of use the shift register...
Hello everyone,
I have a program which set configurations by using write (nrf_drv_twi_tx) in the registers of a sensor.
I use the SDK 8 in the nRF51.
Here is the code...
Hello, I want to test using RTT for logging since I am using UART for send/receive packets. I made following changes in sdk_config.h:
#ifndef NRF_LOG_ENABLED
#define NRF_LOG_ENABLED...
I have device with nrf5x and I will customize this device on production. I use to flashing nrfjprog.
Will prepare one hex file and customize e.g serial number during flashing...
Good time dear Engineers!
Faced with a general Problem.
I use two nRF52 boards connection : Central <-> Peritheral.
init data: MIN/MAX conn intervals = 10/30 ms
...
I noticed that the GPIO port read and port write for SDK v12.2 changed to accommodate chips with more pins but I can't find much information about it. How do I use nrf_gpio_port_out_read...
I want to make a frequency of 750khz, 50:50 duty ratio.
How do I use pwm?
I use it. nRF52832 PCA10040
I used the PWM library example but it failed.
The frequency...
I'm using nRF5SDK V.12.2.0.
In the app_ble_uart example, trying to change MTU size as below.
#define NRF_BLE_MAX_MTU_SIZE 103
...
#if (NRF_SD_BLE_API_VERSION == 3)
...
I am using SAADC with TIMER3 and PPI, sampling 12bits at 250Hz.
When I use 10uS acquisition time, the average current consumption is 300uA lower than when using 3uS or 5uS...
With nrf Toolbox 2.2.1 on android 6.0.1 (Google Nexus 7 or OnePlus 3T), I try to transfer an application firmware in a zip file UiBoardV0.4.1.zip , generated with "nrfutil...
Hi,
In am using a nrf52832 in a serializated configuration, with the softdevice S132 on the connectivity board.
Is there a way to configure GPIO on the connectivity...
hello,
i have one nrf51 dk and it has some advertisement packet, i have another nrf51, i want this another nrf51 to copy first nrf51's data. can you tell me how to copy...
I stumbeled across a problem with my application, which runs on s120. My case is: I have a S120, configured as a peripheral and I have an Android 5.0 Motorola smartphone....
Hi, I'm trying to install the BLE buttonless DFU template onto a nRF52 (PCA10040) eval board using the secure bootloader example (with s132, version 12.2 of the SDK) via nRF...
