Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
Keep hitting my head on this inconvenient workflow.
Edit build config
Select target custom board
Build config
All OK
Edit config again
Target board has been...
I have used the Programmer previously with success. I am attempting to program the Dongle (10059) with a slightly modified version of ble_nusc_usb_dongle. Although it claims...
Hello Team,
I have flashed the bap_unicast_server bluetooth sample on my nRF5340 Audio DK. No build or flash errors. When I connect to my phone it connects properly. I'm...
I'm working on a project involving a USB dongle based on the nRF52840 SDK-2.9.1, which needs to communicate with a sensor (also an nRF52840) and transmit data via USB to PC...
Hello Nordic team, For the ( POC), I configured ADC channel 1 and interfaced a potentiometer to pin P1.14. The ADC was set up accordingly to read raw value from the potentiometer...
I am building a Central BLE app using the Rigado BMD-200 but my current peripherals are running RFDuino code. The peripherals all work with the IOS and Android Apps but I...
I'm using a snippet from the ble_app_uart example and see in the examples:
//static ble_uuid_t adv_uuids[1];
static void advertising_init(void)
{
uint32_t err_code;...
S110 v8.0.0
SDK v8.0.0
ble_app_uart example
I first initialize the services and then initialize advertising. Everything works fine when I do NOT advertise the...
I'm currently trying to make an application using the development kit & I'm trying to use the timer driver, when I induled the C & H files of the driver I got an error : ...
I'm trying to compile the ble_app_beacon_s110_pca20006 project in Kile uVision5 and I get the "cannot open source input file "core_cm0.h": No such file or directory" error...
I am trying to run a NRF51822 chip using Emblocks and OpenOCD, the debugger interface is a ST-Link from a Discovery board, which supports SWD.
When I program the Blank...
Hi,
I bumped into a problem trying to get PWM working and traced it back to the app_pwm_init function, for a simple test case use the the pwm example in the 8.1.0 SDK and...
Hello everybody,
I'm currently trying to start with the nordic development kits, I installed all the tools required to be able to start the development & also I get some...
I am trying to persist characteristic data written by the central side after on_disconnect . I can see the data written inside the evt_write->data ptr and I copy it to store...
Hi Nordic Expert,
Recently I wanna run ble_nus service on my nrf51822 platform, you know, sdk 6.0 does have this demo code in s110 directory, but from sdk 6.1 I cann't...
I'm trying to connect to/program my nrf51822 module I just got. I've got it set up with my st-link but whenever I try to flash the device I keep getting: Error: Flash Download...
I'm trying to enable basic commands with my device. Ideally I have a terminal open on a mac running nodejs or use the UART subapp in the nRF Toolbox App, type a special command...
What's the proper way to debug what's causing my eval board to reset? I'm assuming I need to put a breakpoint in the hard fault handle, but how do I trace that back to the...
Hi,
as a university project, I am currently developing a ultra-low-power temperature and barometer sensor powered just by RF and laser-beam energy. Please see this link...
