Hi everyone.
I am using Visual Studio Code. When i try to compile a simple blink_pwm project, I could not. I am sending output in terminal. What is the main problem and...
Greetings, everyone, I have encountered a configuration(?) problem while trying to setup a lab for a BLE course I am teaching.
The idea is to showcase the vulnerability...
Since NCS 3.0.1 I get the following warning:
warning: Deprecated symbol DEPRECATED_UART_NRFX_UARTE_LEGACY_SHIM is enabled.
... as far as I can see I have not enabled this...
So whatever I try, the only way to get my idle current consumption to an acceptable low value is to set CONFIG_SERIAL=n in my configuration. But then I don't get printk functionality...
Hey, I am working with the Matter light bulb sample from the 2.9.1 SDK, which I have modified to support the occupancy cluster. (nRF-52840 and nRF-52840DK)
This worked fine...
Hello,
I tried to use the Cellular Monitor app within the nRF Connect for Desktop software, but it encountered the following error. I have included the relevant part of...
How can we connect the Thingy:53 to the PPK2 using the included PCA64142 current measurement board, for both Source Meter and Ampere Meter modes?
The PCA64142 board...
Hi, I am newbie at this field.
I have tried to configure network for communication between device nodes.
What i want to do is each device node has unique data( <30bytes...
Hi,
Is it possible to control the ouputs without connecting?
I mean something like this:
I have a nRF51DK. And I would like to detect if there are bluetooth devices...
I'm trying to get some sound out of a piezo buzzer using the PWM library here:
github.com/.../nrf51-pwm-library
My buzzer has a resonant frequency of 2,730Hz. The buzzer...
Hi all,
I am looking for some help on where to identify a problem that cropped up recently. I'm relatively new to the softdevice concept, though it seems straightforward...
Hey everyone,
I'm developing an application using the PCA10001 board. After a while my app crashes. I think this is due to un-freed memory regions. When writing similar...
Hi every one,
I work on application that read continuous analog signal with 500 sample/second and send it from nRF51822 board (1) to nRF51822 board (2) and read this value...
The BT SIG has adopted the "Indoor Positioning Service" and in there it says ...
"When a characteristic value is written, the Server may check the validity of the value...
Hi,
I need to send an audio signal through BLE connection of nRF51822 module, this signal need to quantized and sampled at rate of minimum 8000 sample/second by ADC, i...
I would like a working example of a simple application that uses soft_device (either S110 or S120) plus UART debugging.
I have read many posts in this forum about this topic...
Hi folks,
do you supply a BT Test-SW to set a module with your NRF51822 in different test modes like continuous FH etc. or to change the device to low, mid, high channel...
Hi,
I want to establish a peer-to-peer communication network between 2 nRF51422, such that both the nRF51422 can Transmit as well as Receive data. Is it possible to achieve...
hi,
as we know, the device need to being linked in 1.28s if Advertising types is BLE_GAP_ADV_TYPE_ADV_DIRECT_IND ,but my host can't link device in 1.28s,so i want to link...
Hi,
I try to evaluate DFU using serial but found difficulty. Seeking help here.
I use PCA10028. First, i falsh S110, v8.0 into it.
Then, compile SDK8.0.0\examples...
Hi all!
I want to allow only 1 device to bond at a time. If another device bonding, I want to delete the previously bonded one.
I tried to use dm_device_delete_all() in...
