در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi All,
i would like to know in ble_app_hrs example gpiote_init() is called from main
and then again called in led_start for what purpose it used in 2 place.
can...
I see that we can specify the SPI frequency in bps, I was just wondering how fast the SCK line was oscillating for these values. Does it use the 32.768 kHz crystal oscillator...
If the nRF51 chip is in System Off state, do the GPIO pins retain the pull-ups or pull-downs? If so, what value do they have and how much current can they sink or source?...
Hi all,
when i want to connect different peripheral on central(s120).
it have a error and disconnect.
it seem ok , but that will disconnect later.
ant it get disconnected...
Now I using 51822 to develop a product, I would like to know, can I change the connection interval after connected? or I can only setup the connection interval before connected...
Hi,
is it possible to use the nrf ibeacon which is designed for advertising his data, as i think , to use it also as an observer which can receive data from other beacons...
Hi there,
I am looking for the nRF51 SDK , version 4.3.0
While some previous versions are linked if you click on the version number in the Downloads section (see similar...
Has anyone tried Keil 5.11? I get a parsing error when installing/repairing SDK when it imports the device pack into Keil. 5.10 works great.
The new parser is complaining...
Hi, I cannot install nRFgo Studio 1.17.0.
Installation rollbacks during the installation of libusb 1.0.
My pc has Windows 7 64bit with .Net Framewrok 4.5.
No boards are...
I can't make sniffer working with my HW, everything seems to be working correctly and as described in the help file, but I've never seen any sniffed packet yet. So I've decided...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hello,
We're looking for easy way to communicate between nRF51822 configured as central part with C# application.
Ideally we should use standard firmware which forwards...
