Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command： west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hello,
I have the nRF51822 Evaluation Kit. I have run the basic code examples like 'Blinky' and the BlueTooth HRS (Heart Rate) application, successfully.
Now I would like...
Hi,
Is it possible to give a function address to the "Task End-Point" of a PPI channel?
Like :
err_code = sd_ppi_channel_assign(PPI_CHAN0_TO_TOGGLE_LED,
&(NRF_TIMER1...
I am designing a device that needs to operate both as a Peripheral (such as a Heart Rate sensor) and also as a Central so it can optionally connect and gather data from other...
Hi,
in my application I have a device that has to be controlled by a remote control. For transmitting data between the remote and the device I would like to use BLE (not...
Hello,
Can you please help me with the following questions....
Why table 3 in the softdevice spec shows the same address for the application code_r1_base when softdevice...
I'm having a very strange issue when trying to debug application code on my Nordic platform. I'm hoping that someone else can shed some light on the issue, or at least confirm...
Hi all,
I have followed the guide (AN-29) for using eclipse with the nRF51822 but it gives me several errors.
First at all, the linker says:
...../arm-none-eabi/bin...
Is there an example code anywhere for the nRF51822 to calibrate the internal 32khz RC oscillator using the 16mhz crystal when not using the BLE stack/softdevice?
I would...
Hi,
does firmware or example source code exist for the PCA10000 USB dongle that implements the Bluetooth HID host?
I would like to use it as receiver for the Nordic Smart...
Hi all,
I am trying to specify a fixed port for a L2CAP connection on the nRF51822. The client is a Linux box running bluez (which has BLE support). The client software...
Hi,
Just bought the nRF51822 eval kit. Looks like it came with some great demos for iPhone (nRF_Demo_Utility, nRF_Proximity, nRF_Temp, nRF_UART), but having trouble getting...
Hi,
I upgraded to the 4.3 nRF51 last night and am suddenly having a whole slew of issues:
(1) When flashing the EK, the Segger now reports 257K of Flash (maybe it did...
Hi,
I'm looking to work with a Bluetooth LE master device. From what I read the nRF51822 should be able to function as a Master device (the dongle is configured to be a...
Hi all
I want to load the (UART_example) flash image compile with Keil by nRFgo studio,
but a program fail occur as below screenshot:
any idea?
Thanks.
