Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Hi,
I used to have a URL link for checking ibasis SIM card, such as devices, balances, etc. Now, I cannot find. My SIM card is from Nordic, so the login for ibasis account...
Hi Dev Team,
I am building an application wherein I need to send commands from the Cloud to a Thingy91 device. I tried out the cloud_client sample and I was able to send...
I have seen this problem posted several times in these forums but none of the existing solutions sit right with me.
I have an NRF52840 (using a UBlox BMD-340 dev board...
Hi Dev Team,
I have an application wherein I am publishing my sensor data every hour through MQTT using a Thingy91.
I am storing my sensor data value in a JSON format...
Hi,
I am trying to implement protobuf for my application. I have seen that nano-pb library is there in SDK file. I want to use it in BLE-UART communication. How to do with...
Hello,
I am using RFX2411N RF amplifier in my hardware design. I chose nRF52832 as an MCU. In nRF52832 datasheet, it is mentioned that the pins from P0.22 to P0.31 have...
Hi,
We are currently developing a Zigbee network based on nRF52840.
One of our devices was specially designed to contain 8 endpoints. But when an active ep request is...
Hi,
I'm using the BLE_app_interactive example as a starting point for my prototype (with SDK_17.0.2 and SoftDevice s132 ). I am using nRF52DK to read and write data from...
Hi
Im trying connect two peripheral devices through UART
The example project I used is "examples/peripheral/uart"
But i trace the code, it seems that the driver layer...
Hello,
I've been using nrfx UARTE driver on the nrf5 15.2.0 SDK on a nrf52832 and nrf52840 SoC and noticed that during the boot-up the first byte being sent is 0xFF.
Is...
Can I remove resistor R29 (ENCHG) on the ADP536 to disable the charging function and plug my 3.3V supply into the battery connector?
i.e. use the ADP536 for the power management...
I am working on zigbee network.
I have seen that there is an event for network joining but could not find any event for network disconnection.
If I want to check that...
I'm trying to get LPCOMP working in Zephyr.
I'm getting the following error:
error: 'NRFX_LPCOMP_DEFAULT_CONFIG' undeclared (first use in this function)
I can see that...
Hi, Can anyone explain what the "receiver address correlation" from 2.4GHz Radio documentation means in practice? For example, what can I do as a BLE application developer...
