Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hello i tried a lot but i am unable to Compile this , its is expected examples available in sdk should compile smoothly if there are no changes in it,
i was expecting remote...
Dear Nordic Engineers
Our client wants to make an iPad Pencil, but they are facing a problem: when searching for Bluetooth devices in the [Settings] - [Bluetooth] page,...
Hi Nordic!
I'm evaluating the zephyr samples " broadcast_audio_sink" and " broadcast_audio_source". Running these two on two separate nrf5340 audio dev boards works fine...
Hello! I am trying to set up a central that accepts notifications for two different attributes from a custom BLE service.
I know that the problem is in my discovery process...
I am looking to expand upon the Bluetooth Shell example to convert to USB CDC shell as well as to add other functionality.
I am struggling to locate where the shell commands...
Hello,
I am implementing the periodic search for lte managment (using SDK 2.5.2 on a nrf9160).
The periodic configurations in struct lte_lc_periodic_search_cfg is: ...
In order to compile this sample i had to first update sdk and tools to 2.7.0. In 2.7.0 there is a library error as follows. (D:/Repositories/npm1300_fuel_gauge/src/fuel_gauge...
I'm trying to programm the NRF52833-B-QIAA off board using an Elnec programmer model BeeProg2, but as the revision B of this MCU comes from the factore with APROTECT ENABLE...
Hello, is it possible to reset the battery evaluation using SW without restarting the resources? Unfortunately, I sometimes have to take power directly from the battery, so...
Hello.
Previously, npm1100ic was used. In the npm1100, D+ and D- pins were in ic for usb communication. I don't think there is one in the npm1300. In this case, unlike npm1100...
I am running CoAP client with DTLS enabled on an nRF9161dk.
I poll socket using this code:
I am able to receive data (POLLIN), but when server closes session and sends...
Hi, I am using a module named MS12SF1 (nrf5340 + nrf7002). I was trying to write the Mac address for one time programming by using radio_test sample code. Before doing this...
Hi devzone, I am trying to use the Edge Impulse integration on a Seeed Studio Xiao BLE Sense (nrf52840 based). When I manually download the zip file from Edge Impulse and...
