I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
Hello,
We need to interface the nRF54L15 with a 3-wires SPI slave (which uses one single bidirectional pin for MOSI and MISO).
I see two options here:
1. Connect the...
Issue
On the nrf54lm20 using DTLS with MbedTLS, MbedTLS's heap can be exhausted. This will result in a TLS handshake error. When this issue happens MbedTLS does not catch...
Hey,
I have a question regarding the watchdog in a low power application with dynamic sleep times of e.g. 1mim/10mim/1h. In the docs of nrf9160 and also nrf9151 it says...
Hey Nordic support, We want to perform EMC tests on the DECT NR+ for our product and need a continuous wave or tx tone sample for testing. I found the DECT NR+ shell sample...
I mean like when ever i click pristine build in the vs code i am getting this below error " Unable to build: SDK not found. Ensure that a valid SDK is used for the build configuration...
Hi,
We are using the NRF9151 with AT commands to replace our SIMCOM modems.
We would like to write the SIM profile data to the modem via AT commands just like SIMCOM...
Trying to config TDM SCK for: Master, 4 channels, 24 or 32 bits, 16 KHz...doing the math yields 1.536 or 2.048 MHz for SCK. I have 24 MHz or 32 MHz available as possible clock...
Hello, I have a question regarding external flash erase via `nrfutil` command line tool. Does the `nrfutil device` command support doing a qspi erase with custom qspi commands...
Hello,
There is a minor issue identifying a sysbuild configuration if the initial generate and build fails.
Steps to repro:
- add a kconfig that doesn't exist in...
In the past, I've been told I can bypass a lot of the Zephyr nonsense and use the HAL layers of the nRF Connect SDK directly. So if I want to use what was called nrfx_twim_xfer...
Hello,
I noticed the Audio application explicitly states that WAV sample rates other than 48kHz is not supported.
Is there any risk to modifying the code to support other...
Hello,
In my project, I use both a Bluetooth interface for communication and the PSA functionalities to store and read/use keys. I use the following configuration (excerpt...
Hi Nordic support:
Our product uses the nRF52840. During CE certification, the lab measured the BLE TX power in DTM mode. at –20 °C the power is 3–4 dB higher than at +25...
