I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hello all, We 're working on our custom PCB prototype. We can see current consumption according to this profile even though the flash memory was erased. Also the modem FW...
Hello all,
I have started to port the code from the nRF52dk in Segger EM, indeed, everything so far works on the NRF52 dk , so I have opened the Blinky example for the nRF52820...
Hi,
I am using an nrf52 DK and facing an issue regarding the GPIO voltage levels. The GPIO voltage is around ~2.35V when its in LOW state and slightly increases when in...
Hi,
like mentioned in the caption, i have updated the nRF Connect SDK version from 2.0.0 to 2.0.2 and noticed, that the debugging does not longer work as expected and before...
Hello, I plugged in the nRF52840 dk and LED1 fades in and out. It does not blink. I am unable to connect to my phone. I tried to drag and drop some hex files to the JLINK...
Using the Power Profiler Kit II with
nRF Connect for Desktop (v 3.11.1) on Ubuntu 20.04 with the Power Profiler App v3.4.3
I'm wondering about the value of the time axis...
When operating in high-voltage mode, the spec says that VREGH,DROP is at most 0.3V . What happens if VDDH falls below the programmed VDD output plus VREGH,DROP, for both the...
Dear Community, Following the Nordic's sample of the (<ncs root>/nrf/sample/caf) the LED module & (CAF) Button module demonstrate the LED states & LED effects (awesome!) After...
Hello DevZone,
I'm using nRF5 SDK for Thread and Zigbee v4.2.0 and trying to test Zigbee OTA example and faced some troubles.
I'm following this guide https://infocenter...
I want to use the BLE Secure connection feature with the following options
CONFIG_BT_SMP_SC_PAIR_ONLY=y
CONFIG_BT_SMP_SC_ONLY=y
CONFIG_BT_SMP_APP_PAIRING_ACCEPT=y
CONFIG_BT_SMP_DISABLE_LEGACY_JW_PASSKEY...
Hi
I'm working with a PDM mic for nRF52832 SDK v17.1 on a project and I have a questions about PDM driver working.
Whats the difference between the buffer pointer in nrfx_pdm_buffer_set...
Hi Team
In thingy91---hardware-files-1_6_0.zip, the QM12038 is end of life status now. So do we have any new design to replaced it? Thank you.
www.qorvo.com/.../QM12038...
I just finished the second prototype of a nRF9160 board. First one worked flawlessly, but had poor GPS reception. Rewamped the matching and added SAW filters.
However, now...
I have to switch between several different scanning modes.
I scan in passive mode to get all sensors' advertisements (no connection).
I scan in active mode to get a specific...
Hi everyone
I want use the pwm_driver example of the SDK download at nRF52833 DK
However, some problems were encountered after the migration
I replace the preprocessor...
