I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
When pinctrl is configuring SDA/SDL lines, S0D1 mode is supposed to be enforced as noted by this comment however the function nrf_pin_configure does not use the drive argument...
Hello,
I have the Adafruit nRF52832 Bluefruit LE module, I need to program it through VS Code. I don't have any other J-Link Connector. Is it possible to program the module...
I'm developing a system using BLE Mesh with the intent of having a "collector" node attached to each network that manages provisioning and received published data from connected...
Hello,
It seems that there are no boardfiles or dts files for nRF52840-QFAA in NCS 2.0.0., there is only support for the QIAA version.
Customer built a board with the...
When I use 52832 to develop a mesh project and want to use uart to print information, I find that the code always reports an error because of the existence of printf. The...
Hello, while I was examining the BMD-380 datasheet, a section of which I shared the picture below caught my attention. What does factory image mean? I want to implement Bluetooth...
We are developing a product using the N52810 chip. We have J-link, and by downloading and connecting the Rf test tool,
the result is that there is no firmware. Can you support...
My device and Software details are as below
nRF52840 EVK
Softdevice:s140
SDK v16
We are looking to use freeRTOS instead of zephyr on this board.
Finally with freeRTOS...
Dear Nordic support team
I tried to change the sample of ble_app_uart (nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart\pca10040e) to support connecting 4 mobile...
I am working on an e-paper display with Bluefruit nRF52832 . I need to transfer a large image bitmap over Bluetooth Low Energy (BLE).
As BLE can send 255 bits at once, how...
Hi there,
We are using nrf9160 DK v1.0.0 ( pca10090 ). SES version 5.68 nrf Connect SDK 1.9.1 Windows 10
I want to make it as spi slave on pins CS=p0.10, mosi=p0.11, miso...
Hello Team,
We are developing an application with nRF52832 and ncsv1.8.0.
We are using NUS service to share data between Mobile and Nordic Chip. With the help of nRF...
