I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
Hello, support team.
Now my colleagues are working on the software part for the hardware alpha version of the device with 2 independent antennas for LTE and GNSS. But the...
Hi,
Now I'm using :nRF5_SDK_17.1.0_ddde560\examples\ble_peripheral\ble_app_uart\pca10056\s140\arm5_no_packs.
And I want to add 'Characteristic User Description Descriptor...
Hello,
I'm build my application using v1.9.1 and Visual Code. It seems I have an error saying my application size is greater than the flash size.
I CANNOT jettison any...
I have a big issue about WDT during FDA 510K preparing. I have to proof that WDT of nRF52832 is seperated structurally from main system. since nRF52832 have such a seperated...
To whom it may concern,
I have a project (using Zephyr) where I need to switch UART pins while runtime. Is there a way I can handle this? This is how I initialize pinctrl...
I am using the light_bulb sample from NCS v2.0.0 with an nRF52840 DK board. I changed prj.conf to enable Warning traces from ZBOSS:
+# Enable traces on UART_1 (P1.02) @...
Hello,
I have a question regarding the advertising and scaning mechanism implemented in Zephyr.
To be more precise, suppose the node's radio is in scan mode, and it's...
We want to create solution/project for family of boards using segger embedded studio. We want to create the solution/project in such a manner that new boards software can...
Hello,
I want to build in a reset function for handling certain error states on the 9160DK running nRF Conenct 1.6.0. In the datasheet it appears that nRESET is p0.32 and...
Hi,
I am looking for a way to count the pulses going out of a GPIO pin. If I configure that pin with the input buffer connected, how can I route that signal to a timer/counter...
Hello ,
I am a firmware engineer in Taiwan ,
I already use nRF52820 to finish one case ( cheaper alcohol/acetone BT checker.)
I used USB/ BT wireless uart / Uart send...
Hello,
I have some problems with connecting and interacting with my nRF9160. It doesn't show up in LTE Link Monitor, only got "No supported devices connected" - If i have...
Hello,
nRF52832, SEGGER Embedded Studio for ARM V4.12
We want to improve BLE transmission speed between nRF52832 and iPad mini.
Now condition and transmission speed...
I have two devices:
NRF52832_xxAA_REV2
NRF52840_xxAA_REV3
Running the Zephyr blinky sample application with the following KConfig option added:
CONFIG_NRF_APPROTECT_LOCK...
