Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I have read through similar posts, though none seem to talk directly about the DK and the JLink OB (SAM IC) missing bytes itself.
To start off with, I have created a basic...
From various pages I copied together this code to read the reset reason:
However, I believe most of those pages were for nRF5 SDK. (It's not always clear.)
Is this still...
Hi Nordic
I used the nrf_gpio_cfg_sense_input() API to initialize the GPIO4 for waking up nrf52832 from system off mode, This IO could wake up nrf52832 successfully, but...
These two func:"softdevice_ble_evt_handler_set "
and "softdevice_sys_evt_handler_set" suggests that there are two categories/sets of events grouped into system & BLE.
...
I'm a user of nRF52 DK with S132.
I want to modify the event handler in the example application code such as ble_uart_c.
Where can i find the full list and description of...
Hello
Can I use the LORAWAN module with NRF52833? if yes, is the LORA gateway also required to send the data to the cloud, or can it be done directly without a gateway?...
TX :52840
Software version：nRF5_SDK_16.0.0_98a08e2 hardware version：
RX:52820
Software version：nRF5_SDK_17.1.0_ddde560
My test method: send 60 bytes of data through...
Hi:
I use sdk:nRF5_SDK_17.0.2_d674dde and NRF52840.
Reference examples:nRF5_SDK_17.0.2_d674dde\examples\peripheral\uart
PC connection RX-pin20 and TX-pin22, PC sends...
Hi,
We are looking to purchase the nRF52832 SoC. The data sheet says it supports a data rate of 1Mbps when the receiver sensitivity is set to -103dBm. This data rate is...
I am experiencing a strange behavior with SES 6.32, using GCC and I wonder if I should choose a different compiler.
COMPILING THIS PART OF CODE (I added line numbers for...
I want to add wifi connectivity to asset_tracker. It is required that MODEM is turned off. The program flow need to change so that instead of Modem, wifi Module is tried first...
Hello,
I am trying to read a 32-bit value over BLE but the value displays as 8-bit on nRF Connect. In my code I am sending it as an int32. Why does nRF Connect only show...
Hi There,
I have almost done the project, I used nrf52832 as central(master) and nrf52810 as peripheral(slave).
i use the blinky example and everything working fine. I...
Hello,
I am using nRF52840 and I currently am working on a application where mostly I am using central functionality (BLE connection and exchange the data) along with cellular...
I'm willing to use the 5 claused licensed code for the parts that only work with nordic hardware, but the partition manager isn't actually necessary. Is there some way to...
