I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
Hello,
We've encountered an issue where if the ZED missed a network key update, it will not do trust center rejoin and continue to do secure rejoin Using nRF5 SDK for Thread...
Trying to west build -b nrf52840dongle_nrf52840 results in a qspi_nor flash error but the dongle hasn't defined any qspi_nor flash.
(This sample builds correctly with the...
Hi,
I want to output debug message(printk) through USB port on nrf52840 dongle. how to config it in zephyr, I have read the HelloWorld project code, but got nothing,
...
Hi,
I'm trying to make my nrf52840 dongle a ble central device. I did worked with the usbd_ble_uart example succesfully, but I was trying to add the ble_app_uart_c to it...
Isn't it supposed to autocomplete that? If I complete it to k_msleep(1000); the application builds and runs fine.
VS Code 1.67.2 nRF Connect for VS Code Extension Pack 2022...
Hi there,
We have a custom board that runs on a nRF52833 chip.
In order to flash firmware to that board, I use the Nordic DK (PCA10056), and connect my custom board to...
I've just installed the Nordic SDK version 17.1, SES version 6.3, and Segger J-Link Software version 7.64e on a new Ubuntu 22.04 laptop.
I've installed everything in their...
Hello everyone
I am using BLE Peripheral UART and Central UART samples to send data between two nrf5340 dev. kits.
I'm trying to set the directed advertising on the peripheral...
Hi All!
I am using nrf52820/33/40 devices. Able to connect central (1) and peripheral (4) concurrently.
Central is an end node(nrf52820) that is connected to the sensor...
Hello Team,
We are looking forward to use Long Range Advertisements in our application. Our current application is based on nRF52832 + ncsv1.8.0.
Per our knowledge...
Hello, We're developing an LPN product that will leave the mesh and stay off the mesh for up to 3 days (possibly more). When it rejoins the mesh, the central server/gateway...
Hello, I am currently working on the nrF52840 module with the soft device s140.
My job is to read the values from different characteristics.
The characteristics are...
Having developed a dual-role Central and Peripheral BLE app, I've been trying to use the Dongle to do power measurements. My app works fine in VSCode with the nrf52 on a RF9160DK...
Hi,
I'm getting a hard fault that I really need some help to debug. My call stack is shown below and includes nrf_log_frontend_dequeue() as well as a custom service function...
Hi,
I have made an emitter (with nRF52833) and a receiver (with nRF52833 too) and i already succeed to receive data and print IQ data from an antenna array but the IQ data...
