The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
Hi,
I am developing a react native app with the iOS and Android NRF mesh lbrary. In this app I am handling connection, data receiving on characteristic and sending on...
Hi
I'm evaluating using the nRF52805 for an application that would use BLE but require almost no BLE functionality. Only the ability to periodically wake up and scan is...
Greetings. We are using the zigbee/shell sample in order to verify the connectivity of some other devices running the zigbee stack. While the shell sample had no issues in...
Hello,
I want to create a Matter network using my nRF5340 DK board, as Matter accessory, and my RaspberryPI, as controller (CHIP Tool controller). I'm using as well nRF...
1.SDK:SDK17.1
2.IAR V9.2
3.
static float inv_sqrt(float x) { float xhalf = 0.5f * x; int i = *(int *)&x;
i = 0x5f375a86 - (i >> 1); // this is magic. x = *(float ...
Hello,
I am developing a door lock system. Where in final product door lock will be controlled and monitored by BLE+Zigbee. So far I have complete success of controlling...
Hi, I'm developing an application using UARTE to reading response from Module Sim. The content response from Module Sim has 495 characters. When I debug, I only read some...
Hi.
I am developing nRF52832 and ST7789.
I'm trying to print out the text, but it's not working properly.
The nrf_gfx_screen_fill() function works fine.
When I proceed...
Hi
I can't set CommonName in the attributes list while generating a private key, it gives an error:
Omitting CN it works fine:
What am I doing wrong?
Thanks...
Hi
I have a question concerning AOA.
I have already make a tx (with nrf52833) and a rx (nrf52833 too) and i succeed to receive the CTE and the IQ sampling with the antenna...
Hello ,
my team and i we are trying to set a communication by UART between two nrf52840 µC , with one of the µC we have done a communication with a nucleo board which supports...
Hello all,
I have made a simple app that runs in loop on the nRF52DK, in general it reads data from the sensor via twi and turns on the leds ...
When the program is run...
Hi, i am developing Zigbee window covering device on nrf connect sdk 1.9.1v which has 2 endpoints, but i am face issue when zigbee command is received and
device_interface_cb...
I have Ebyte’s E73-2G4M08S1C (nrf52840-QIAAC0/ aQFN73 module) where P0.19, P0.21 and P0.23 are not wired out :(
So, my question is which other pins could use / not use instead...
